CN Series
ANSI CN Series Water Centrifugal Pump
End-suction water pump built to ANSI/ASME B73.1 with a full open impeller and ANSI B16.5 flanges
View specifications
Contact
Send the Duty and We Will Send the Selection
Send us the duty and the liquid, and we will come back with a series, a size and the specifications that are published for it.
How to Reach Us
One Channel That Carries Attachments
We do not use contact forms. Email reaches us directly and lets you attach a pump curve, a nameplate photograph or a specification without retyping anything.
The more of the checklist below you can send with the first message, the more of the answer comes back in the first reply.
| [email protected] | |
| Telephone | TBCNo telephone number is published on the Flowsteer site |
| TBCNo WhatsApp number is published on the Flowsteer site | |
| Address | TBCNo postal address is published on the Flowsteer site |
| Working hours | TBCNot published on the Flowsteer site |
We publish contact details only where the Flowsteer site publishes them. Anything shown as TBC above is unconfirmed rather than withheld.
Two polypropylene lined centrifugal pumps with stainless flanges on the assembly floor
Enquiry Checklist
Six Things That Turn One Reply Into an Answer
- Flow and headFlow in m3/h and total head in metres — static lift plus friction losses at the design flow.
- Supply frequency50 Hz or 60 Hz. The FA series publishes 1450 to 2900 rpm at 50 Hz and 1750 to 3500 rpm at 60 Hz, and the curve moves with speed.
- The liquidWhat it is, its temperature, and its solids percentage if it carries any. This decides the wetted material and the impeller type.
- Flange standardDIN2501, ANSI B16.5 150LB or 300LB — whatever is already on the pipework.
- Existing pump detailsIf this is a replacement: the nameplate, the size designation and the flange rating of the pump coming out.
- ScopeBare shaft pump, or a complete set with motor, coupling, guard and baseplate.
Straight to a Product
Enquire About a Specific Series
CI Series
ISO CI Series Water Centrifugal Pump
ISO 2858 and ISO 5199 back-pull-out end-suction pump, fully interchangeable with other ISO brands
View specifications
KCP Series
KCP Series Lined Water Centrifugal Pump
Horizontal single-stage pump in PP, PE and UHMW-PE for water that attacks metal wetted parts
View specifications
DE Series
DE Series Water Centrifugal Pump
Process-duty water pump from DN 25 to DN 400 with flow to 600 m³/h for water and waste water
View specifications
FA Series
FA Series EN733 Horizontal Centrifugal Pump
BS EN733 / DIN24255 end-suction pump, 2 to 1100 m³/h and head to 152 m, for building services fire and irrigation
View specifications
VNP Series
VNP Vertical Sump Pump
Vertical single-stage sump pump in polypropylene for wet-pit installation with solids to 20 percent
View specificationsQuestions
Contacting Flowsteer
How quickly will I get a reply?
Response times are not published in the source catalogue so we do not quote one. Send the duty point with the first message and the first reply will carry the selection rather than a request for more information.
Why is there no enquiry form on this page?
Because email carries attachments and a form does not. A pump curve, a nameplate photograph or a specification sheet tells us more in one message than a form ever will.
Can I send a drawing or a specification?
Yes, attach it to the email. Drawings, curves, nameplate photographs and specification extracts are all useful.
Do you supply directly or through distributors?
Tell us your location and the project and we will confirm how supply is handled for that market.
Attach the Curve the Nameplate or the Specification
Anything that describes the duty gets a faster and more accurate answer than a description typed from memory.