Sanitary elbow
Clamp Elbow
Clamp end elbows SK-EB003 SK-EB004 and SK-EB006 in 45 and 90 degrees.
View specifications →
12 items SS304 and SS316L DIN SMS 3A ISO IDF
Sanitary Valves Clamps Elbows Tees And Reducers DN15 To DN200
The parts between the pump and the tank: butterfly and diaphragm valves, check valves, clamps, elbows, tees, reducers, sight glasses and spray balls, all polished for hygienic service.
The Range
Twelve Line Components From One Standard
Every item is offered in SS304 or SS316L with mirror or matt polish, in weld, clamp or thread connection, so the whole line shares one material and one standard.
Sanitary reducer
Clamp Reducer
Concentric clamp reducers SK-RD003 and SK-RD004.
View specifications →
Sanitary tee
Clamp Tee
Clamp end tees SK-TE003 SK-TE007 and SK-TEE008 for branch connections.
View specifications →
Butterfly valve
Sanitary Butterfly Valve
Manual or pneumatic butterfly valves DN15 to DN200 in SS304 or SS316L.
View specifications →
Check Valve
Sanitary Check Valve
Non return valves SK-CV001 and SK-CV002 for hygienic lines.
View specifications →
Diaphragm Valve
Sanitary Diaphragm Valve
Diaphragm valves that keep the working parts out of the product.
View specifications →
Sanitary elbow
Sanitary Stainless Steel Elbow
Weld end sanitary elbows SK-EB001 SK-EB002 and SK-EB005.
View specifications →
Sight glass & spray ball
Sight Glass
Inline sight glasses SK-SG001 and SK-SG002 for hygienic lines.
View specifications →
Sight glass & spray ball
Spray Ball
Fixed spray balls SK-PL001 and SK-PL002 for tank cleaning.
View specifications →
Sanitary clamp
Tri-Clamp
Clamps SK-CL001 to SK-CL003 with gaskets to match the line.
View specifications →
Sanitary reducer
Welded Reducer
Weld end concentric reducers SK-RD001 and SK-RD002.
View specifications →
Sanitary tee
Welded Tee
Weld end sanitary tees SK-TE002 SK-TE004 and SK-TE006.
View specifications →Who Buys This Line
- Dairy beer and beverage plants building or modifying process lines
- Pharmaceutical and biotechnology fabricators
- Skid builders who need the pump and the line from one source
- Maintenance teams replacing worn valves and seals on an existing line
Problems It Solves
Mixed standards on one line
DIN on one section and SMS on another means adapters and dead legs. Buying the fittings as a set keeps the standard consistent from tank to filler.
Seals fail against the cleaning chemistry
Silicone, EPDM and fluoroelastomer sealing materials are available so the gasket survives the CIP regime rather than the other way round.
Finish does not meet the audit
Mirror polish to Ra below 0.5 um is available across the range, which is what a hygienic audit looks for on wetted surfaces.
Why This Line
What You Get Across The Range
One Size Band
DN15 to DN200, or half inch to eight inch, across valves and fittings so a line can be built end to end.
Pressure And Temperature Stated
Maximum working pressure 1.0 MPa, 10 bar, with vacuum on the low side and a working temperature band from minus 5 to 95 degrees.
Manual Or Actuated
Valves are supplied for manual operation or with a driving device where the line is automated.
Application Scenarios
Where These Parts Sit
Between Tank And Pump
Clamps, elbows and reducers making the connection from vessel outlet to pump suction without dead legs.
On The Filling Line
Butterfly and diaphragm valves controlling flow to the filler, with sight glasses so the operator can see product moving.
Inside The Vessel
Spray balls fixed in the tank head, feeding the CIP cycle that cleans the vessel between batches.
Industries Served By This Line
Selection Guide
Ordering Fittings That Fit
Confirm The Standard
DIN, SMS, 3A, ISO or IDF. Measuring an existing fitting is the safest way to be sure before ordering.
Choose Material And Finish
SS304 or SS316L, mirror polish to Ra below 0.5 um or matt polish, depending on product and audit requirements.
Match The Seal To The Chemistry
Silicone, EPDM or fluoroelastomer, chosen for the product and the cleaning solution, not just for temperature.
Decide Connection Type
Weld for permanent runs, clamp where the line is opened for inspection, thread where the plant standard calls for it.
Answers
Sanitary Valves And Fittings FAQ
Which sizes do you supply?
DN15 to DN200, which is half inch to eight inch, across the valve and fitting range.
Which standards are available?
DIN, SMS, 3A, ISO and IDF. Tell us which one the existing line uses so the new parts land on it directly.
What is the pressure rating?
Maximum working pressure is 1.0 MPa, which is 10 bar, and the minimum is vacuum. Working temperature runs from minus 5 to 95 degrees Celsius.
Which sealing materials can I have?
Silicone, EPDM and fluoroelastomer. The product and the cleaning chemistry decide which one, so tell us both.
Can the valves be automated?
Yes. Valves are supplied for manual operation or with a pneumatic driving device for automated lines.
Engineering Notes
Guides For This Line
Buying Guide
DIN SMS 3A ISO And IDF How To Order Fittings That Actually Fit
Five standards, similar looking parts, different dimensions. Measuring one existing fitting saves more time than any catalogue.
Read the guide →
Material Guide
SS304 Or SS316L Choosing The Grade For Tanks Pumps And Fittings
The difference is molybdenum and carbon content. What that means on your plant is chloride resistance and how the material behaves after welding.
Read the guide →
Process Guide
Choosing A Sanitary Pump That Survives Your CIP Cycle
The pump has to move product gently and then take hot caustic at full flow. Those two requirements pull in opposite directions, and the elastomer usually loses.
Read the guide →Send A Line List Not Just One Part Number
Sizes, standard, material and seal for the whole line gets you one quotation and one delivery instead of five.