FC Fast Connector (Ref 282)
FC Fast Connector (Ref 282) is part of the field assembly/fast connector range built by Ever Expresslink Limited in Ningbo, China. It is built on the FC (Ferrule Connector) interface.
Mechanical field termination without a fusion splicer
Interested in FC Fast Connector (Ref 282)
Email the model and quantity with your destination country. We reply with pricing, lead time and a datasheet.
Product Overview
FC Fast Connector (Ref 282) is part of the field assembly/fast connector range built by Ever Expresslink Limited in Ningbo, China. It is built on the FC (Ferrule Connector) interface.
The screw coupling keeps end-face contact stable when the rack is vibrating or when technicians work on neighboring ports, which is why FC stayed the default on test sets, monitoring gear and older carrier equipment. FC needs the alignment key to seat in the adapter slot before the nut is tightened. Cross-threading a keyed FC is the single most common cause of high loss on an FC link.
It is one of 6 items in this range. A typical application is restoring a broken patch cord in a live cabinet. What the range is built to give you there: re-usable versions let a failed termination be corrected on the spot.
The problem it addresses is re-work when a field termination fails and has to be redone. A practical note that applies across this range: insert until the fiber visibly bows slightly, then lock the mechanism. Specifications for a particular configuration are confirmed on the quotation rather than assumed from the designation.
Key Benefits
- Supplied as FC Fast Connector (Ref 282), so the part you receive matches the designation you ordered against
- No fusion splicer, no power and no splice protection sleeve needed
- Termination in minutes rather than a splicing setup cycle
- Re-usable versions let a failed termination be corrected on the spot
- Visual confirmation of fiber insertion on designs that provide it
Problems It Solves
- Fusion splicers that are too expensive to put in every van
- Drop terminations that need doing in a stairwell with no power
- Emergency restoration where a splicer is not available
- Training burden for crews who only terminate occasionally
Application Scenarios
- Optical test and measurement ports
- Enterprise fiber repairs by non-specialist staff
- Terminating a subscriber drop at the premises
- Restoring a broken patch cord in a live cabinet
- MDU riser terminations where a splicer cannot be set up
Who It Is For
- Building and MDU cabling contractors
- Maintenance crews doing emergency restoration
- Enterprise IT teams making occasional fiber terminations
- FTTH drop installation crews
Technical Features
- FC (Ferrule Connector) interface
- FC needs the alignment key to seat in the adapter slot before the nut is tightened. Cross-threading a keyed FC is the single most common cause of high loss on an FC link.
- Hand-tool assembly with no power required
- Designs for 250 µm, 900 µm and drop cable
- SC and FC bodies in UPC and APC polish
- Factory-polished fiber stub inside the connector
Materials
- Zirconia ceramic ferrule with pre-polished stub
- Index-matching gel
- Mechanical splice element
- Thermoplastic housing and boot
Specifications
| Product Designation | FC fast connector |
|---|---|
| Product Family | Field Assembly/Fast Connector |
| Connector Interface | FC (Ferrule Connector) |
| Manufactured In | Ningbo, China |
| Warranty | One year against defects in materials and workmanship |
Values shown are those carried by the product designation. Dimensional and optical values for a specific order are confirmed on the quotation.
Manufacturing Process
- Stub fiber termination and polish in the factory
- End-face inspection of every stub
- Mechanical splice element assembly
- Gel dosing and sealing
- Function sampling and packing
Quality Control
- Stub end-face inspection before assembly
- Trial field termination and loss measurement per lot
- Mechanical splice retention force sampling
- Gel presence and sealing verified
- Packing count verified before dispatch
Customization Options
- SC or FC body
- UPC or APC polish
- Fiber acceptance for 250 µm, 900 µm or drop cable
- Kitted with cleaver and cleaning consumables
- Private-label packaging for rollout programs
Compared With Other Options
| SC | SC seats faster with a push-pull motion; FC holds up better where the cabinet vibrates or ports get bumped |
|---|---|
| ST | ST twists on with a bayonet in a quarter turn; FC's threaded nut takes longer but resists loosening |
Handling FC Fast Connector (Ref 282)
Before You Order
- Use a precision cleaver; cleave angle is the main cause of high loss here
- Clean the fiber with a lint-free wipe before insertion
- Insert until the fiber visibly bows slightly, then lock the mechanism
In Service
- Verify with a visual fault locator or power meter before closing up
- On reusable versions, re-cleave rather than reusing a damaged fiber end
- Record which terminations were mechanical rather than fusion spliced
Questions About FC Fast Connector (Ref 282)
What do you need from us to quote FC Fast Connector (Ref 282)?
The quantity, the destination and anything that has to match on your side: connector and polish at each end, fiber mode and core size, and length where the item is an assembly. If you are matching a part you already buy, send the sample and we will quote against it.
Can FC Fast Connector (Ref 282) be supplied with a different connector interface?
Yes. FC (Ferrule Connector) is what this designation carries, and the same family is stocked across the other mainstream connector standards. Tell us the port you have to mate with and we will confirm the equivalent part.
Can a fast connector be reused if the termination fails?
Reusable versions allow the mechanism to be released so the fiber can be re-cleaved and re-inserted. Single-use versions cannot. Confirm which type you are ordering if field re-work matters to you.
What fiber types can be terminated?
Versions are available for 250 µm coated fiber, 900 µm tight-buffered fiber and flat drop cable. Tell us what your crews actually carry and we will match the part.
Do I need special tools?
A precision cleaver and the matching hand tool. No power, no fusion splicer and no heat-shrink oven. Cleaver quality has a direct effect on the loss you achieve.
More Field Assembly/Fast Connector
SC Field Assembly Fast Connector
Specifications SC Field Assembly Optical Connector SC Field Assembly Optical Connector Specifications SC Quick Assembly Connector, Fast Connector: Factory-installed.
View Details
SC Fast Connector (Ref 279)
Used for mDU riser terminations where a splicer cannot be set up.
View Details
SC Fast Connector (Ref 286)
Used for restoring a broken patch cord in a live cabinet.
View Details
SC Fast Connector (Ref 284)
Used for terminating a subscriber drop at the premises.
View DetailsGuides Cases and Industries
Installing Field Assembly Fast Connectors
A step by step method, the cleave quality that decides the result, and an honest account of what you trade against a fusion splice.
Deployment ProfileField Drop Termination Without A Splicer
Terminating a subscriber drop with a cleaver and a hand tool, and knowing what that trade costs
Deployment ProfileMDU Riser Fiber Distribution
Distributing fiber up an apartment riser so units can be connected one at a time without disturbing the rest
IndustryFTTH and Broadband Operators
Drop-side and distribution hardware for networks whose cost is decided per subscriber
Request Pricing For FC Fast Connector (Ref 282)
Tell us the quantity and destination. If you are matching a part you already buy, send the sample and we will quote against it.