Manufacturing
Our solutions are pivotal in the manufacturing sector, where precision and efficiency are paramount. From equipment that enhances production lines to tailored solutions that optimise processes, the aim is the same: facilities operating at peak performance.
Pain Points In Manufacturing
Where manufacturers lose throughput.
Material That Will Not Stay Flat
Blanks that bow after cutting slow every downstream operation and show up as rework in assembly.
Cutting That Stops The Line
Stop and cut shearing caps line speed and wastes material at every crop.
Component Failures In Motion Systems
Bearings and drive joints that fail early take a whole line with them, not just the component.
What Buyers In This Sector Need
- Consistent flat feed material for pressing and forming
- Cutting accuracy that holds at production speed
- Components rated for continuous rather than intermittent duty
- Fast technical answers during line design
Typical Application Scenarios
- Cut to length lines producing blanks for forming
- Precision levelling of thin strip before stamping
- Conveyor and transfer systems in production plants
- High speed cutting of sheet and strip
Recommended Products
What manufacturers order most often.
Cut to Length Line With Precision Leveling
Servo driven cut to length line holding length deviation within ±0.5 mm at speeds to 120 m/min.
View Details
Multi Roll Leveler for 0.08-1 mm Copper Strip
Copper strip leveler for 0.08-1 mm material used in electrical and electronic components.
View Details
High Speed Fly Shear for Continuous Strip Cutting
Rotary fly shear cutting at line speed, up to 2500 strokes per minute with carbide tipped blades.
View Details
Precision Work Rolls 9-68 mm With Hard Chrome Plating
Chrome plated work rolls, HV 800-1000 surface hardness, matched to chrome plated back up rolls.
View Details
Full Complement Cylindrical Roller Bearings 20-1200 mm
SL series full complement bearings from 20 mm to 1200 mm for high radial load duty.
View Details
Circle Shear for 0.15 mm Strip Slitting Lines
Rotary circle shear trimming edges on very thin strip down to 0.15 mm thickness.
View Details
Flying Shear for Continuous Rolling Lines
High speed head and tail cropping at full line speed without deceleration or stoppage.
View Details
Cut to Length Machine With Tension Leveler
Q235A welded frame machine with hydraulic servo system for stainless strip cut to length work.
View DetailsHow We Deliver
From requirement to running equipment.
Material, gauge, output and the accuracy the finished part needs.
A customised project plan produced from your production requirement.
Production to the drawings fixed in the technical agreement.
Installation guidance, personnel training and production commissioning.
Delivery Capability
- Molding and sampling committed under 50 days
- More than 60 automatic production machines
- One stop project management through commissioning
- Spare parts and consumables after handover
What You Get From Ascon
- Throughput improvement measured against your current process
- Product consistency from equipment that holds its settings
- Engineers with more than eight years of industry experience each
- A single contract from design through commissioning
Project References
1660 mm Scale Breaker Roll Units For A Wide Cold Rolling Pickling Line
Precision roll units and cassettes for the scale breaking section of a 1660 mm wide cold rolling pickling line handling 0.5-12 mm strip.
Read More
Tension Leveler For A 1550 mm Galvanizing Line
A tension leveler configuration for carbon steel strip on a 1550 mm galvanizing line, with the chrome plated roll set to keep it consistent.
Read MoreRelated Technical Articles
How Frac Pump Bearing Quality Keeps A Fracturing Job On The Design Curve
Displacement, pressure and uptime are one chain in hydraulic fracturing, and the power end bearing sits in the middle of it.
Read More
Edge Trimmer Shearing Principles For Metallurgical Strip Lines
Side clearance and overlap are the two settings that decide whether you get a clean shear or a burr.
Read More
Choosing A Multi Roll Straightener Configuration For Mixed Materials
One machine can straighten high strength steel, stainless and titanium, but never with the same parameters.
Read MoreManufacturing FAQ
Can you design equipment for a process we have not automated yet?
Yes. The feasibility stage produces a customised project plan from your production requirement before any drawing is fixed.
How fast can you sample?
We commit to molding and sampling in under 50 days so your development timeline is not held up.
Do you supply components as well as machines?
Yes. Bearings, rollers and drive joints are supplied to manufacturers who build their own equipment.
What accuracy can a cut to length line hold?
Our servo driven configuration holds cut length deviation within 0.5 mm at speeds up to 120 m/min.
Can you integrate with our existing automation?
Yes. Tell us the control system and the signals available and we design the interface into the scope.
Improve A Production Step
Describe the process and the result you need and our engineers propose equipment or components.