A 300 x 600 mm hydraulic surface grinder for small and medium parts in tool rooms and production plants.
The MY3060 is a hydraulically traversed surface grinder with a 300 x 600 mm table and a 600 kg load rating. Longitudinal stroke is 550 mm and cross travel is 300 mm, which covers the plate and block work most tool rooms see daily. It is rated for Ra 0.32 micron surface roughness, so parts leave the machine finished rather than needing a second operation.
Who it is for: Mould and die shops, jig and fixture makers, machine rebuilders, and production plants in machinery, steel, energy, automotive, aerospace, weapons and shipbuilding that finish small and medium sized parts in house.
The table is moved by oil rather than by hand, which removes the reversal marks a handwheel leaves at each end of the stroke.
A full die shoe or a stack of plates can be ground in one setup, so parallelism is referenced once instead of three times.
Tall fixtures and stacked workholding fit under the wheel without stripping the machine down.
Rated finish is fine enough for sealing faces and sliding surfaces that would otherwise go out for lapping.
Milling leaves cusps and stress relief distortion, particularly after heat treatment. A hydraulic surface grinder takes the face back to a single reference plane.
Hand traversed tables mark the workpiece where the operator reverses. Hydraulic traverse holds a constant speed through the full stroke.
At Ra 0.32 micron the ground face is usually the final face, removing an outside operation from the routing.
Cast iron bed, column and table with hardened and ground slideways. Wheel, magnetic chuck and coolant filtration are specified with the machine to suit the workpiece material and hardness.
Figures below are taken from the machine data sheet. Anything not documented is marked as to be confirmed rather than estimated.
| Table size (X by Y) | 300 x 600 mm |
|---|---|
| Horizontal travel of worktable | 300 mm |
| Longitudinal stroke of worktable | 550 mm |
| Max centre of wheel to table | 500 mm |
| Maximum load | 600 kg |
| T slot of worktable | 14 mm x 1 |
| Grinding wheel size (max) | 300 x 30 x 127 mm |
| Grinding wheel speed | 1450 rpm |
| Surface roughness | Ra 0.32 micron |
| Machine overall dimensions (L x W x H) | 1800 x 1650 x 1900 mm |
| Machine weight | 1550 kg |
Six stages, each of them completed in our own hall in Shenzhen before the machine is crated.
Within the WUK surface grinding range the MY3060 is the manual feed starting point. The AHD models add servo vertical feed and longer travels.
| Model | Key Specification | Best Suited To |
|---|---|---|
| MY3060 | 300 x 600 mm table, hydraulic traverse, manual down feed | Tool room work and lower batch volumes |
| 3060AHD | 300 x 600 mm table, 720 mm X travel, automatic down feed 0.1 to 8 mm | Repeat production on the same table size |
| 4080AHD | 400 x 800 mm table, 950 mm X travel, three T slots | Larger plates and heavier fixtures |
The table is 300 x 600 mm with 550 mm of longitudinal stroke and 300 mm of cross travel, carrying up to 600 kg.
No. The MY3060 uses manual down feed with hydraulic longitudinal traverse. If you need automatic down feed between passes, look at the 3060AHD, which shares the same table size.
The machine is rated at Ra 0.32 micron. Achieved finish depends on the wheel, the dress condition, the coolant and the material.
Chucks are quoted with the machine rather than assumed, because pole pitch should match your part size. Send your typical part dimensions and we will specify one.
In a plywood case lined with plastic film, bolted to the case base. We quote EXW, FOB, CFR or CIF from Shenzhen.
12 months warranty on the machine, with setup, wheel selection and fault finding support from our engineers on WhatsApp or email.
Servo vertical feed and hydraulic table traverse on a 300 x 600 mm table.
The largest table in the WUK surface grinding range, at 400 x 800 mm with 950 mm of X travel.
OD and ID grinding on one machine, for shafts, bushes, needle valves and plungers.
Tell us your supply voltage and frequency, the parts you intend to grind and the accessories you need. We reply with a configured quotation and a dated schedule.
