Servo vertical feed and hydraulic table traverse on a 300 x 600 mm table.
The 3060AHD combines hydraulic left and right table traverse with servo controlled vertical feed and stepped cross feed. Automatic down feed runs from 0.1 to 8 mm, so a roughing and finishing sequence completes without an operator on the handwheel. X travel is 720 mm on a 300 x 600 mm table rated for 600 kg.
Who it is for: Tool rooms moving from one off work to repeat batches, die shops running scheduled maintenance grinding, and production plants that need a surface grinder an operator can load and leave.
The cycle steps the wheel down on its own, which is what makes the tenth part match the first one.
Vertical handwheel graduation is 0.005 mm per division over 1 mm per turn, so finishing passes are set deliberately.
Overtravel at both ends means the wheel fully clears the workpiece, removing the burn mark that happens when it stops on the part.
Table and wheel speeds are specified for both supply frequencies, so the machine is correct wherever it lands.
Manual down feed varies with whoever is on shift. Automatic feed from 0.1 to 8 mm makes the cycle the same every time.
A short X travel leaves the wheel dwelling on the edge of the part. 720 mm of travel on a 600 mm table clears it completely.
Rapid traverse at 990 mm per minute at 50 Hz and 1190 mm per minute at 60 Hz cuts the dead time between cutting passes.
Cast iron bed, column and saddle with hardened ground slideways. Servo drive on the vertical axis. Wheel and chuck specified with the machine.
Figures below are taken from the machine data sheet. Anything not documented is marked as to be confirmed rather than estimated.
| Table size (X by Y) | 300 x 600 mm |
|---|---|
| X axis travel | 720 mm |
| Y axis travel | 360 mm |
| Max centre of wheel to table | 520 mm |
| Maximum load | 600 kg |
| Table T slot specification | 14 mm x 1 |
| Table speed | 5 to 25 m/min |
| Hand wheel feed graduation | 0.02 mm per division over 5 mm |
| Automatic feed | 0.1 to 8 mm |
| Rapid moving speed (50 Hz / 60 Hz) | 990 / 1190 mm/min |
| Grinding wheel size (max) | 350 x 40 x 127 mm |
| Grinding wheel speed (50 Hz / 60 Hz) | 1450 / 1740 rpm |
| Z axis hand wheel graduation | 0.005 mm per division over 1 mm |
| Z axis rapid speed | 230 mm/min |
| Spindle motor | 5 x 4 HP |
| Z axis motor | 750 W |
| Hydraulic motor | 2 x 6 HP |
| Cooling motor | 90 W |
| Y axis motor | 80 W |
| Machine overall dimensions (L x W x H) | 2000 x 1900 x 1810 mm |
| Machine weight | 2200 kg |
Six stages, each of them completed in our own hall in Shenzhen before the machine is crated.
The 3060AHD sits between the manual MY3060 and the larger 4080AHD, on the same 300 x 600 mm footprint as the MY3060.
| Model | Key Specification | Best Suited To |
|---|---|---|
| MY3060 | Manual down feed, 550 mm stroke, 1550 kg | Lower volume tool room work |
| 3060AHD | Automatic down feed, 720 mm X travel, 2200 kg | Repeat batch grinding on medium parts |
| 4080AHD | 400 x 800 mm table, 950 mm X travel, 2600 kg | Larger plates and heavier fixtures |
It identifies the automatic hydraulic configuration with servo controlled vertical feed, as opposed to the manual down feed MY3060.
Yes. The machine is specified for both, with wheel speed at 1450 rpm on 50 Hz and 1740 rpm on 60 Hz. Confirm your supply when you order.
The Z axis handwheel is graduated at 0.005 mm per division over 1 mm per turn, and automatic feed is adjustable between 0.1 and 8 mm.
Yes, the machine steps forward and backward on the cross axis under control, driven by an 80 W Y axis motor.
The machine itself measures 2000 x 1900 x 1810 mm and weighs 2200 kg. We confirm crated dimensions on the proforma invoice.
This model uses servo feed with conventional controls. If you need full CNC, the WK22 punch grinder and the CNC version of the WK1420x500 are the machines to look at.
The largest table in the WUK surface grinding range, at 400 x 800 mm with 950 mm of X travel.
A 300 x 600 mm hydraulic surface grinder for small and medium parts in tool rooms and production plants.
CNC punch and pin grinding from 1 mm up to 150 mm, internal and external.
Tell us your supply voltage and frequency, the parts you intend to grind and the accessories you need. We reply with a configured quotation and a dated schedule.
