Automotive Parts
Injection molded automotive parts built from tools that hold their form across a full production run
All 12 Automotive Parts
Automotive Air Handling Housing
Deep-ribbed black housing with a large circular bore and integrated ducting, molded as one piece.
View details →
Automotive Interior Trim Bezel
Slim black bezel frame with a molded-in clip rail and a Class-A visible face.
View details →
Automotive Intake Manifold
Long black manifold body with plenum, runner ports and bolt flanges in a single molding.
View details →
Automotive Air Filter Housing
Ribbed black housing shell with sealing lip and mounting bosses around the perimeter.
View details →
Automotive Headlamp Housing
Black headlamp housing with twin reflector bowls, connector apertures and adjuster pockets.
View details →
Automotive Lamp Housing with Reflector Cavities
Angular lamp body combining dark structure with light reflector zones in one tool.
View details →
Automotive Coolant Expansion Tank
Translucent tank body with a filler neck, level-readable wall and molded mounting feet.
View details →
Automotive Tail Lamp Lens
Two-color lens with a clear light-guide section blended into a deep red signal section.
View details →
Automotive HVAC Air Vent Register
Black vent register with twin circular barrels, louvre frame and a ducted rear body.
View details →
Automotive Under Hood Bracket Assembly
Wide structural bracket with a corrugated conduit run and molded-in retaining clips.
View details →
Automotive Speaker Grille Cover
Flat cover panel with a fine perforated acoustic field and snap-fit edge features.
View details →
Automotive Mirror Cap
High-gloss curved mirror cap with a clean unbroken Class-A outer surface.
View details →What Goes Wrong Here
Automotive programs fail on the second year, not the first. A lamp housing that creeps out of flatness, a manifold that starts to flash at the slide shut-offs, a Class-A mirror cap that begins to show a weld line after the first cavity polish — each one stops a line that cannot be stopped.
Our Answer
Every automotive tool we build is filled, packed, warped and cooled in MoldFlow before the cavity block is roughed, and the DFM that comes back to you carries the gating, parting line, draft study and cooling layout in writing.
Who This Is For
- Tier 1 and Tier 2 automotive suppliers sourcing tools out of Asia
- Lighting specialists needing optical-grade cavity finishes
- Under-hood component makers with slide and lifter heavy geometry
- Interior trim suppliers with Class-A visible surfaces
Where These Parts Are Used
- Front and rear lighting assemblies
- Air intake and air handling systems
- Cooling and coolant circuits
- Interior trim, vents and covers
From Enquiry to Delivered Tool
- Step 1
Quotation within two working days from your 3D data, resin and volume
- Step 2
Full 3D mold design completed and reviewed, with the DFM sent for your comment
- Step 3
CNC and EDM machining with inspection after machining and on the electrodes
- Step 4
Mold trial, trial report and sample dimension report, then final and packing inspection
Where Automotive Parts Are Sourced
Automotive Parts — Questions We Are Asked
How many automotive parts do you show?
12, all photographed from our own work. Each one has its own page with the tooling route behind it.
What is the lead time on tooling for automotive parts?
Lead time depends on the size of the tool, the number of cavities and the side actions involved, so we put it in the quotation rather than publishing one figure. The quotation itself comes back within two working days. Programme lead times: TBC per project.
Which mold standard will you use?
Yours if you have one. Otherwise DME, Meusburger, HASCO, Progressive or MISUMI — naming it in the enquiry avoids re-specifying components later in the design.
Will we see a design before you cut steel?
Yes. The mold design is completed to one hundred percent detail, checked in a design review meeting, and sent to you together with the DFM for comment before fabrication starts.
What do you need to quote automotive parts?
3D part data, the resin, the expected annual volume and the mold standard. With those four items we can quote without a second round of questions.
Quote a Automotive Part Tool
Send us the part and the volume. A professional mold quotation with technical comment comes back within two working days.