Capsulated Slip Rings
Industry
Slip Rings for Test Rigs Turntables and Inspection Equipment
Endurance rigs, rotating test stands, antenna measurement turntables and inspection equipment need instrumentation signals to survive thousands of hours of rotation without drift.
Industry Pain Points
What Goes Wrong on These Axes
Constraint 1
Measurement signals are small, so contact noise in the joint shows up directly in the data.
Constraint 2
A rig that runs unattended for weeks cannot afford a connector that needs servicing.
Constraint 3
Sensor counts grow through a project, so the channel count has to be planned with headroom.
How INGIANT answers it
Precious metal contacts, a dynamic resistance variation below 10 mΩ and insulation resistance above 1000 MΩ at 500 VDC are the standard electrical values on INGIANT catalogue units, and USB, Ethernet and fibre channels are added where the instrumentation needs them.
Suitable Families
Product Families That Fit This Industry
141 models
Capsulated Slip Rings
A capsulated slip ring is a sealed cylinder with a solid shaft: the rotor turns, the stator stays still, and both ends leave the…
8 models
USB Slip Rings
A USB slip ring keeps a USB device on a rotating platform enumerated and streaming while the platform turns without limit.
201 models
Through Bore Slip Rings
A through bore slip ring carries power and signals around a hollow centre, so a drive shaft, a hydraulic line, an optical cable…
62 models
Fiber Optic Rotary Joints
A fibre optic rotary joint passes light across a rotating interface, so bandwidth, isolation and immunity to electrical noise…
Products
Recommended Models
A starting point — the full family pages carry every model.
Capsulated Slip Rings
DHS045-95 DHS045-95 Ingiant OD 45mm rotor flange slip ring transmits 81…
Through Bore Slip Rings
DHK120-12-002 Ingiant ID 120mm through hole slip ring with 12 channels power…
Through Bore Slip Rings
DHK080-33 Ingiant standard through hole slip ring hole diameter 80mm with 33…
Fiber Optic Rotary Joints
DHS055-11-2F Ingiant Photoelectric Slip Ring OD 55mm with 2 channels optical…
Fiber Optic Rotary Joints
DHS066-39-1F Ingiant Optoelectronic slip ring OD 66mm with 1 single mode…
Delivery Capability
What You Get With the Part
Lead time
7–15 days for standard products, 10–20 days for simple customisation and 15–40 days for complex customisation.
Quality system
ISO 9001, GJB9001C and GB/T 19001-2008 / ISO 9001:2008, with electrical and functional testing before despatch.
Warranty and support
12 months from date of sale, with regular technical information and training support and direct engineer contact by email or WhatsApp.
Knowledge
Articles on Test and Measurement
2025-09-11
What are the differences between explosion-proof conductive slip rings and ordinary conductive slip rings?
What are the differences between explosion-proof conductive slip rings and ordinary conductive slip rings? Explosion-proof slip…
2024-05-24
What is a high-speed slip ring? High speed slip ring manufacturer
Facebook Twitter LinkedIn What is a high-speed slip ring? High speed slip ring manufacturer What is a high-speed slip ring?…
2024-05-10
Slip rings for cameras Monitoring equipment slip rings
Facebook Twitter LinkedIn Slip rings for cameras Monitoring equipment slip rings The advancement of science and technology has…
FAQ
Test and Measurement Questions
How much contact noise should I expect?
Catalogue units specify a dynamic resistance variation below 10 mΩ, with insulation resistance of 1000 MΩ or more at 500 VDC.
Can I add channels later?
Plan spare rings into the original design. Adding circuits later means a new ring stack, so specifying headroom at the start is cheaper.
Do you supply units for antenna measurement turntables?
Yes, including RF rotary joints and combinations of RF with power and signal rings.
Specify a Rotating Connection for Test and Measurement
Send the rotating speed, the installation envelope, the circuit count, the signal types, the temperature range and the IP requirement and INGIANT comes back with a design.