Stainless Steel Sheet
Cold rolled 0.3 to 3 mm and hot rolled 3 to 120 mm sheet and plate in 304 316L 409 and 2205 duplex, up to 2500 mm wide and 12000 mm long.
Every Product in This Category
Sheet and plate is where finish, width and flatness decide whether the fabrication goes together. This category runs from the ferritic exhaust grade 409, through 304 and 316L for general and chloride service, up to 2205 duplex where strength lets you take thickness out, with mirror and hairline finishes for architectural work.
409 Stainless Steel Plate and Sheet
Grade 409 is a thermostable ferritic stainless steel with better oxidation and corrosion resistance than carbon steel. This…
View specifications →
316L Stainless Steel Sheet
Grade 316 is the standard molybdenum bearing austenitic stainless steel, second only to 304 in importance. The molybdenum gives it…
View specifications →
2205 Duplex Stainless Steel Sheet
2205 duplex stainless steel, UNS S32205 and S31803, is a 22 percent chromium, 3 percent molybdenum, 5 to 6 percent nickel and…
View specifications →
Hairline Finish Stainless Steel Sheet
A hairline finish is a directional surface where the metal carries a straight, fine grain running the length of the sheet. The…
View specifications →
Mirror Finish Stainless Steel Sheet
A mirror finish is a bright non directional surface polished with a 1000 grit abrasive belt and then buffed. EN 10088-2 classifies…
View specifications →
304 304L and 304H Stainless Steel Sheet
Grade 304 is the standard 18/8 austenitic stainless steel and the most widely used stainless grade, available in the widest range…
View specifications →Problems This Category Solves
- Panel to panel finish mismatch when grit and grain direction are not controlled
- Weld decay in heavy gauge plate that cannot be solution annealed after welding
- Excess weight when a design is driven by the low yield strength of 316L
- Extra joints forced by width and length limits
Who Buys It
- Tank, vessel and ducting fabricators
- Architectural metalwork and fit out contractors
- Automotive exhaust and hot end pressing shops
- Distributors stocking sheet across finishes
What the Works Can Actually Produce
- Cold rolled 0.3 to 3 mm and hot rolled 3 to 120 mm meeting at 3 mm with no gap
- Width to 2000 mm on austenitic sheet and 2500 mm on 2205 duplex
- Length to 12000 mm or customised
- Nine finishes from No.1 hot rolled annealed and pickled to No.8 mirror
- 904L plate rolled from 0.3 mm to 350 mm for heavy acid service
Typical Applications
- Chemical process tanks and scrubber internals
- Automotive exhaust systems and heat shields
- Architectural cladding, lift interiors and signage
- Food and pharmaceutical equipment panels
Where This Material Ends Up
Chemical Processing
Chemical plants are where material selection stops being a cost decision. Sulphuric, phosphoric, acetic,...
Automotive and Transport
Exhaust systems are a cost and durability problem at once. The material has to survive condensate, road salt...
Food and Pharmaceutical
Hygienic equipment is judged on what it does not do: it does not shed metal into the product, it does not...
Marine and Shipbuilding
Seawater is a stagnant chloride solution with biology in it, and that combination takes apart alloys that...
Stainless Steel Sheet Questions Buyers Ask
How wide can you roll stainless sheet
Which finish should I specify for architectural panels
Do you supply plate thicker than 120 mm
What is the minimum order for 304 sheet
Why is tolerance important when buying plate
Can you cut sheet to our size
Get a Quotation for Stainless Steel Sheet
Send the grade, the size, the wall or thickness, the quantity and the destination port. A quotation with lead time and certificate level comes back the same working day where possible.