FL-20 Color Cooled SONY CMOS Camera for Fluorescence Imaging

Key Benefits

• 20 megapixel resolution captures full sample detail in a single shot with 5472 x 3648 pixel output
• Cooled CMOS sensor reduces dark current to 0.001e-/pixel/s for clean long-exposure fluorescence imaging
• 14 frames per second at full resolution over USB3.0 enables real-time observation without lag
• Supports 2x2, 3x3, and 4x4 binning to increase frame rate or reduce data load
• Real-time intelligent image processing improves contrast and sharpness without sacrificing speed
• Can operate up to four cameras simultaneously using the SDK for multi-channel imaging setups
• 16-bit or 8-bit output allows flexible data handling for scientific and documentation workflows

Application Scenarios

• Fluorescence imaging in biological or medical research labs requiring long exposure with minimal noise
• High-resolution documentation of microstructures in metallurgy or semiconductor inspection
• Multi-camera imaging setups in microscopy labs using synchronized capture across multiple instruments
• Long-exposure imaging of weakly fluorescent samples where dark current must be minimized
• Teaching or demonstration sessions where real-time image quality and clarity are critical

Who It Is For

• Research and clinical laboratories performing fluorescence microscopy
• Quality control teams in semiconductor and materials science requiring high-resolution imaging
• University teaching labs using digital microscopes for advanced microscopy instruction
• Microscopy system integrators building multi-camera imaging platforms
• Industrial inspection lines needing low-noise, high-resolution capture for defect analysis

Problems It Solves

• Uncooled CMOS cameras generate excessive hot pixels during long exposures, corrupting fluorescence data
• Low frame rates at high resolution make real-time observation difficult during sample alignment
• Lack of binning options limits performance when speed or data volume must be reduced
• Single-camera systems cannot support synchronized capture across multiple microscopes
• Insufficient bit depth or image processing leads to loss of detail in low-contrast samples

Technical Features

• Sony IMX183CQJ-J CMOS sensor with 15.86mm diagonal image area for wide coverage
• 20 megapixel resolution at 5472 x 3648 pixels with 2.4μm x 2.4μm pixel size
• Rolling shutter mode with exposure time range from 18μs to 60 minutes
• Peak quantum efficiency of 84% at 535nm, ideal for green fluorescence detection
• Readout noise below 1 electron, minimizing signal degradation
• Real-time intelligent image processing for enhanced contrast and clarity
• Supports 2x2, 3x3, and 4x4 binning to adjust resolution and frame rate
• USB3.0 interface enables 14fps at full resolution and powers the camera
• C-mount optical interface ensures compatibility with standard microscope objectives
• Operating temperature range 0 degC to 40 degC, humidity 10% to 85% for stable lab use

Specifications

Specifications are taken from the AMADA product data for this item. Confirm critical dimensions with us in writing before ordering.

Customization Options

• C-mount interface allows direct attachment to standard microscope objectives
• Support for 2x2, 3x3, and 4x4 binning to adjust resolution and frame rate for different workflows
• 16-bit or 8-bit output selection based on data storage and processing needs
• SDK integration allows custom software control for multi-camera or automated imaging systems
• Compatible with PC configurations meeting minimum CPU and RAM requirements

Comparison With Other Options

Use Guide

• Ensure the microscope objective is mounted with a C-mount adapter before attaching the camera
• Use a PC with at least Intel Core i5 and 8GB RAM to run the Mosaic V2 software and maintain full frame rate
• Enable binning (2x2, 3x3, or 4x4) if you need higher frame rates or reduced data volume
• Set exposure time to 18μs for fast events or up to 60 minutes for long fluorescence exposures
• Use the real-time image processing feature to enhance contrast and sharpness during live viewing
• Connect the camera to a USB3.0 port; the camera draws power from the same cable
• For multi-camera setups, use the SDK to synchronize capture across up to four FL-20 units