- Home
- Stone Processing
Diamond Tools for Every Stage of Stone Processing
Stone processing is a chain: block extraction, squaring, slab sawing, calibrating, grinding, polishing and edge work. A tool that is wrong at one station costs yield at every station after it. This is the largest part of our programme, with 53 products in 20 categories.
What Goes Wrong and What Fixes It
Edge chipping on marble and limestone
Soft stone chips when the bond is too hard and the blade polishes instead of cutting. The marble series runs a free-cutting bond and the continuous-rim blades close the segment gap that causes most chips.
Segment loss mid-block
On a 900-3500 mm block blade, losing segments means stopping the saw and losing the block face. Segment specification follows your saw power, not a catalogue default.
Thickness variation reaching the polishing line
If slabs arrive at different thicknesses the polishing heads cannot hold gloss. Calibrating rollers fix that before the line, not after.
Kerf loss on valuable stone
Every millimetre of kerf is stone you cannot sell. Thin turbo blades and multi-wire cutting exist to reduce it.
Where the Tools Are Used
Quarry
Diamond wire for extraction and squaring, with rubber and spring configurations in the same bead diameter.
Block yard
Block cutting and horizontal cutting blades from 350 to 3500 mm, plus loose segments for re-tipping.
Slab plant
Multi-saw blades and matched sets, gang saw segments and calibrating rollers.
Fabrication shop
Bridge-saw edge cutting blades, angle-grinder blades, cup wheels, finger bits, core bits and profile wheels.
Polishing line
Metal and resin bond fickerts, magnesite abrasives, flexible pads and polishing buffs in one graded sequence.
On site
Dry-cutting concave blades, brazed tools and flexible dry pads for installed stone.
Stone Processing — 20 Categories
Diamond Grinding Cup Wheel
Cup wheels for grinding granite marble and engineered stone
Browse category →
Small Diamond Saw Blades
Angle-grinder and table-saw blades for granite marble and engineered stone
Browse category →
Diamond Wire for Stone
Diamond wire and beads for quarry squaring profiling and multi-cutting
Browse category →
Diamond Segments for Stone
Loose segments for re-tipping gang multi and circular saws
Browse category →
Flexible Diamond Pad
Flexible diamond pads and buffs for wet and dry stone polishing
Browse category →
Block Cutting Blade
Large-diameter blades for primary block cutting
Browse category →
Edge Cutting Diamond Blade
Bridge-saw edge cutting blades for granite and marble slabs
Browse category →
Magnesite Abrasives
Magnesite abrasives for granite and marble polishing lines
Browse category →
Diamond Fickert for Stone
Metal and resin bond fickerts for granite and quartz slab lines
Browse category →
Concave Dry Diamond Blade
Curved-body blades for dry curve cutting in natural stone
Browse category →
Diamond Core Bits for Stone
Core bits for drilling natural and engineered stone
Browse category →
Cross Cutting Diamond Blade
Cross cutting blades for marble slab trimming
Browse category →
Diamond Finger Bits
Finger bits for opening holes and truing saw lines in stone
Browse category →
Horizontal Cutting Blade
Horizontal cutting blades for block trimming on granite and marble
Browse category →
Diamond Profile Wheel
Profile wheels for edges and corners on natural and engineered stone
Browse category →
Diamond Roller for Stone
Calibrating rollers for slab thickness control
Browse category →
Diamond Multi-saw Blade
Multi-blade saw blades for high-throughput slab production
Browse category →
Tuck Point for Stone
Laser-welded tuck point blades for joint and slot work in stone
Browse category →
Polishing Buff for Stone
Polishing buffs for final gloss on stone surfaces
Browse category →
Resin Bond Grinding Disc
Resin bond grinding discs for stone surface work
Browse category →Where Most Enquiries Start
Arrow Segment Diamond Grinding Cup Wheel for Stone
Arrow segments for fast stock removal on stone
View specifications →
Continuous Rim Diamond Grinding Cup Wheel for Stone
Continuous rim for the smoothest ground surface
View specifications →
Continuous Rim Diamond Grinding Cup Wheel with Slot
Slotted continuous rim balancing finish and cooling
View specifications →
Double Row Diamond Grinding Cup Wheel for Stone
Double row cup wheel for heavier stock removal
View specifications →
Flower Turbo Diamond Grinding Cup Wheel for Stone
Flower turbo geometry for aggressive stone grinding
View specifications →
L Segment Diamond Grinding Cup Wheel for Stone
L segments silver-brazed for side grinding
View specifications →
Resin Filled Diamond Grinding Cup Wheel for Stone
Resin-filled wheel for a finer ground surface
View specifications →
Single Row Diamond Grinding Cup Wheel for Stone
Single row cup wheel for controlled grinding
View specifications →
Straight Turbo Diamond Grinding Cup Wheel for Stone
Straight turbo profile for even grinding on stone
View specifications →
T Segment Diamond Grinding Cup Wheel for Stone
T segments for edge and corner grinding on stone
View specifications →
Turbo Wave Diamond Grinding Cup Wheel for Stone
Wave turbo cup wheel for cooler stone grinding
View specifications →
Wave Turbo Diamond Grinding Cup Wheel for Stone
Wave segments for fast cooling on long passes
View specifications →How We Handle These Orders
Specification first
Material, machine, size and quantity decide the bond. Every quote starts there.
Sequence supply
Stations that depend on each other are quoted together, not item by item.
Re-tipping
Loose segments for 200-3500 mm blades, gang saws and multi saws.
Export packing
Shipped from Shangqiu, Henan on standard export terms.
Related Solutions
Stone Processing — Questions From Buyers
Do I need different tools for granite and engineered quartz
Often yes. Quartz is resin-bound, so it loads a bond that works on granite. Tell us which you run most and we adjust the specification.
Can you supply a full polishing sequence
Yes. Magnesite for rough calibrating, metal bond fickerts for rough and medium grinding, resin bond fickerts for the finer steps, then buffs. Supplying the sequence as a set is the point.
What is the largest blade you make
The block cutting programme runs to 3500 mm diameter. Segments for those blades are also sold separately for re-tipping.
Tooling for stone processing
Send your station list or your current tool and the material you process.