- Home
- Products
- Press Locked Grating
- Press Locked Grating 30x2 Stainless Steel
Press Locked Grating 30x2 Stainless Steel
Light stainless press locked panel with matched 30x2 bearing and cross bars, acid passivated, for hygienic floors and light-duty visible decks.
Product Overview
The lightest press locked section in the range: 30 mm deep, 2 mm thick, with a cross bar of the same section, so again a square mesh but in a panel light enough to lift and hose down daily. It is specified where cleaning matters more than load, which describes most floor grating in food production, kitchens and laboratories. Because the joint is pressed rather than welded there is nowhere for product residue to sit in a weld fillet, and acid passivation after fabrication is what keeps the surface from picking up rust spots after the first few washdowns.
Key Benefits
- Light enough to lift and clean daily without mechanical handling
- No weld fillet for residue to collect in, which matters in hygiene audits
- Square mesh in a light section, so the panel still looks finished
- Acid passivated after fabrication, including cut ends and frames
At A Glance
- Family
- Press Locked Grating
- Category
- Press Locked Grating
- Material
- stainless Steel
- Bearing bar
- 30 x 2 mm
- Cross bar
- 30 x 2 mm
- Surface treatment
- Acid passivation
What It Looks Like
Photographs of this product taken by the factory, lit and in production. Nothing here is a rendering of a product that does not exist yet.
Who It Is For
- Food and beverage plant engineers
- Hygiene and cleaning contractors specifying liftable floor panels
- Laboratory and cleanroom fit-out contractors
- Hospitality operators replacing corroded kitchen grating
Problems It Solves
- Floor panels too heavy for cleaners to lift every shift
- Residue trapped in weld fillets failing a hygiene inspection
- Rust spots appearing on stainless panels that were never passivated
- Galvanized panels that cannot survive a daily chemical washdown
Application Scenarios
- Food production floor grating lifted for daily cleaning
- Commercial kitchen and beverage line floors
- Laboratory and cleanroom service areas
- Light-duty walkways where appearance matters
Technical Features
- Bearing bar 30 x 2 mm stainless steel
- Cross bar 30 x 2 mm stainless steel, press locked
- Square mesh geometry with no welded joints
- Acid passivation after fabrication
- Panel size set for single-person lifting
Published Specification
Every row below is reproduced from the manufacturer's published specification for this range. Rows shown in italics are figures the specification does not publish; those are confirmed in writing rather than estimated here.
| Material | stainless Steel |
| Bearing bar | 30 x 2 mm |
| Cross bar | 30 x 2 mm |
| Surface treatment | Acid passivation |
| Structure | Press Locked Grating |
| Panel size | Made to your drawing |
| Place of production | Yantai, Shandong Province, China |
| Brand | ShengJingYe |
| Minimum order quantity | Small batch accepted |
| Load class | TBC, confirmed in writing against your loading |
| Lead time | Confirmed in writing per order, not published |
Use Guide
- Size panels to what one person can lift wet, not dry
- Cap or round the banding where panels are handled every shift
- Keep stainless tools and stainless brushes for these panels only
- Rinse cleaning chemicals off rather than letting them dry on the surface
- Inspect the frame seating when panels are back down after cleaning
Quality Control
- Panel weight and size checked against the lifting requirement
- Joint lock-up sampled across the run
- Passivation applied after all fabrication, then inspected
- Edges checked so cleaners are not handling sharp banding
Materials
- Stainless steel bearing bar and cross bar, grade TBC
- Passive layer restored by acid passivation after fabrication
Manufacturing Process
- Drawing and 3D model
- Cutting and stamping
- Pressure welding or press locking
- Framing and fabrication
- Surface treatment
- Inspection and packing
Certification Standards
Production follows TBC, the source specification publishes no certification marks. Certificates are sent per product on request rather than posted publicly, because the documents a shipment needs depend on the destination market.
Customisation Options
- Panel size to the lift your cleaning team can manage
- Rounded or capped edge detail for frequent handling
- Frames and channel surrounds in matching stainless
- Cut-outs for drains and equipment feet
How It Compares With The Alternatives
A technical comparison against other ways of solving the same problem. Nothing here is a performance claim against a named competitor product.
| Against a stock panel cut to fit on site | A stock panel trimmed on site loses its banding, its bar pitch at the edge and its coating at every cut. This one is drawn to the opening and coated after it is fabricated. |
| Against buying the panel and its frame separately | Panel, banding, hooks, frame and handrail are fabricated and coated in the same plant and the same batch, which is what makes them fit each other. |
| Against another family in this range | See the Press Locked Grating page for what this family does that the others do not, and the related products below for the nearest alternatives. |
Press Locked Grating 30x2 Stainless Steel Questions
How heavy is a panel?
Will a 2 mm bar take a pallet truck?
Why does passivation matter here?
Can panels be made with capped edges?
Products Buyers Shortlist Alongside This One
Press Locked Grating 40x3 Stainless Steel
Stainless steel press locked panel on 40x3 bearing bar with a 10x2 cross bar, acid passivated, for platforms and visible runs with a flush top surface.
See the specification
Press Locked Grating 32x3 Carbon Steel
Hot-dip galvanized carbon steel press locked panel with 32x3 bearing bar and a matching 32x3 cross bar, giving a deep square mesh.
See the specification
Welded Steel Grating 30x2.5 With Flat Cross Bar
Pressure-welded carbon steel panel on 30x2.5 bearing bar with an 8x2 flat cross bar, hot-dip galvanized, for general platform, walkway and trench duty.
See the specificationGuides That Cover This Product
Where It Has Been Installed
Request Press Locked Grating 30x2 Stainless Steel
Send the finished size, the quantity, the mounting and the destination market. A quotation and the full specification come back by email.