Cooler LED Module
Neon Strip Multiple Beam Angle For Cooler Application
Lensed neon flex at 120 LEDs per metre and 10W per metre with a 25 degree beam
View Specifications →
LED Module
3D Bending Wall Washer Neon Flex Washing 3 To 5 Metres
3D bending neon body with a wall wash lens reaching a 3 to 5 metre washing height
Email [email protected] or call and WeChat 0086-15986651902
Product Overview
What This Product Is And Who It Is For
This build combines the two things that normally cannot go together: a neon body that bends in any direction and free cuts, and a lens that throws a controlled wall wash 3 to 5 metres up a surface. Single colour builds run 24 LEDs per metre at 20W per metre with 1600 to 2000 lm/m, and RGB, SPI and DMX versions share the same body. Beam angles run from 15 degrees to 30 x 45 degrees.
Key Benefits
Why Buyers Choose This Build
Washing height over 3 to 5 metres, so one line at the base can light a whole facade storey
3D bending and free cutting on a lensed wall washer, which most lensed products cannot do
Single colour, RGB, SPI and DMX builds on the same body for mixed static and dynamic facades
IP67 waterproof design for permanent exterior installation
Application
Where It Fits And What It Fixes
Who It Is For
- Facade and architectural lighting contractors
- Exterior feature and landscape lighting installers
- Specifiers who need a stated wash height for a facade calculation
Problems It Solves
- Facades where a grazing detail has to follow a curve and still wash the wall evenly
- Schemes needing 3 to 5 metres of wash height from a single line at floor level
- Projects that would otherwise use straight lensed sections and visible joints on a curve
Application Scenarios
- Building facade wash
- Curved architectural features
- Exterior decorative structures
- Landscape and hardscape walls
Technical Features
- 3D bending wall washer neon flex
- Quality silicone with extrusion process for a softer strip
- Lens with different beam angle selections
- Wall washing height over 3 to 5 metres
- 3D bending design, bends in any direction
- Free cutting design, cuts at any length
- Waterproof design reaching IP67
Specifications
Specification Table
Figures below are the published specification for this build. Where a value is set per order it is stated as such rather than estimated.
- Ingress Protection
- IP67
- Voltage
- 24V constant voltage
- Power
- 12W to 20W per metre
- LED Density
- 24 per metre
- Washing Height
- Over 3 to 5 metres
- Efficiency
- 80 to 100 lm/W on white builds
- Flux
- 1600 to 2000 lm/m on white builds
- Beam Angles
- 15, 30, 60, 30 x 45 and 25P20 degrees
- Bending
- 3D, any direction
- Cutting
- Free cutting
Part Number Table
| Product Model | LED Package | CRI | SDCM | CCT | Luminous Angle | Drive | Voltage | LEDs Per Metre | Efficiency | Flux Per Metre | Power Per Metre |
|---|---|---|---|---|---|---|---|---|---|---|---|
| LK-FV2416024283520-8XX-FWD2721 | 2835 | 80 / 90 | Below 3 | 2700-6500K | 15 / 30 / 60 / 30 x 45 degrees | Constant voltage | 24V | 24 | 80-90 lm/W | 1600-1800 lm/m | 20W/m |
| LK-FV2416024303020-8CW-FWD2721 | 3030CW | 80 / 90 | Below 3 | 2700K + 6500K | 25P20 degrees | Constant voltage | 24V | 24 | 90-100 lm/W | 1800-2000 lm/m | 20W/m |
| LK-FV2416024303020-RGB-FWD2721 | 3030RGB | - | - | R 620-630nm, G 520-530nm, B 465-475nm | - | Constant voltage | 24V | 24 | R 20, G 47, B 8 lm/W | 520 lm/m | 20W/m |
| LK-FV2416024303012-SPI-FWD2721 | 3030RGB | - | - | R 620-630nm, G 520-530nm, B 465-475nm | - | Constant voltage | 24V | 24 | R 20, G 47, B 8 lm/W | 300 lm/m | 12W/m |
Manufacturing
How It Is Made Checked And Customised
Materials
- Extruded silicone neon body
- 2835 and 3030 LED packages
- Optical lens array
- Flexible FPC carrier
Manufacturing Process
- SMT placement
- Reflow soldering
- Lens fitting
- Silicone extrusion over the lensed board
- IP67 verification
- Lit and beam check
- Reeling
Quality Control
- Incoming LED binning to SDCM 3
- Lens alignment check inside the body
- IP67 immersion verification
- Beam and wash height verification
- Lit inspection
Certifications
- CE
- RoHS
Customisation Options
- Beam angle selection
- Colour and control protocol
- Body dimension
- End cap and connector
Comparison
How It Compares With Other Products In The Range
Compared With Neon Strip 3D Bending And Free Cutting
The same bending and cutting freedom without the wall wash lens
Compared With Wall Washer Strip Light High Efficiency Lens Series
A flat IP67 wall washer reaching 3000 lm/m where bending freedom is not needed
Use Guide
Specifying And Installing It Correctly
- Set the offset from the wall against the chosen beam angle and the target wash height
- Cap every free cut, as the IP67 rating depends on the end seal
- Mock up the wash on the actual surface, since texture changes the visible result
Related Products
Other Products Worth Comparing
LED Module
Neon Strip DMX SPI Media Ribbon IP67 1516
Pixel controlled media ribbon at 10 pixels per metre in DMX and SPI, IP67
View Specifications →
LED Module
Neon Strip Slim Digital Neon Flex Strip Light
The slim neon body at 6 x 14 mm and 8 x 16 mm, up to 140 LEDs per metre
View Specifications →
Cooler LED Module
Neon Strip Side Bending Digital Neon Flex
Side bending neon flex in two body sizes, single colour through to DMX RGBW
View Specifications →Go Deeper
Industry Pages And Guides That Cover This Product
Architectural Facade Lighting
A facade installation is permanent, exposed and seen from a distance.
Read More →
Design Guide
Top Bend Side Bend And 3D Bend Neon Flex Explained
Which way a neon flex body bends is the first thing to establish, because it decides whether the detail on the drawing can be built as drawn.
Read The Guide →
Installation Guide
Wall Washer Beam Angles And Mounting Distance
A wall washer is only as good as the relationship between its beam angle, its offset from the wall and the height it has to cover. Get that wrong and no amount of output fixes it.
Read The Guide →FAQ
Wall Washer Neon Strip 3D Bending FAQ
How high will it wash?
Over 3 to 5 metres, depending on the beam angle and the offset from the wall.
Can it bend around a curve?
Yes, the body uses a 3D bending design and bends in any direction.
What is the output per metre?
1600 to 1800 lm/m on the 2835 build and 1800 to 2000 lm/m on the 3030 dual colour build.
Are colour and pixel versions available?
Yes, RGB and SPI builds are listed on the same body.
Request A Quote For Wall Washer Neon Strip 3D Bending
Tell us the quantity, the colour temperature and the profile it has to fit. We will confirm the part number and the lead time.