API V11 Valve Pairs
API V11 Ball and Seat
Matched carbide valve pairs for subsurface sucker rod oil well pumps
Product Detail
Industry Application
Tungsten Carbide for Petroleum and Gas Equipment
Carbide parts for oil exploration and well completion including ball and seat valve pairs oil shaft sleeves drilling bushes flow beans carbide tubes and valve cores.
Industry Pain Points
What Fails in This Sector
- Sand laden well fluid cuts steel and hardfaced surfaces within a single run
- A leaking valve pair ends pump efficiency and forces a rod string pull
- Erosion changes flow geometry so chokes and beans stop metering correctly
- Downtime cost is far higher than the price of the wear part itself
Customer Needs
What Buyers Actually Need
- Wear surfaces that keep their geometry in abrasive multiphase flow
- Matched pairs and sets rather than loose components
- Repeatable dimensions so parts stay interchangeable across rebuilds
- A manufacturer who works from drawings rather than a catalogue
Related
All Product Categories
Recommended Products for Petroleum and Gas
Carbide for Oil Industry
Carbide Sleeves
Large carbide sleeves with drilled hole patterns including 176 hole and 82 hole designs
Product Detail
Carbide for Oil Industry
Carbide Cores and Seats
Valve cores seats flow beans and drilling bushes for well completion equipment
Product Detail
Carbide Tubes
Carbide Tubes and Bushes
Ground bore and outside diameter for pump sleeves guide bushes and flow parts
Product DetailTypical Applications
Where the Parts Are Used
- Subsurface sucker rod pump standing and travelling valves
- Well completion valve internals and flow control
- Shaft sleeves and drilling bushes in downhole assemblies
- Carbide flow beans and valve cores
Delivery Capability
What We Can Deliver
- Documented sleeve production at OD 268 mm x ID 228.6 mm x H 160 mm with 176 holes
- Sleeves with 82 hole patterns
- API V11 series valve pairs and ball and seat blanks
- Sinter-HIP densification before machining
Solution Flow
Solution Route for Petroleum and Gas
1. Requirement ReviewDrawing sample or failure photos reviewed by an engineer
2. Grade DirectionAbrasion or impact dominated load case discussed with you
3. Drawing ApprovalGeometry and critical dimensions agreed in writing
4. ProductionPressing Sinter-HIP and machining to the approved drawing
5. InspectionCritical dimensions checked before packing
6. Export DeliveryProtected packing and documents for your clearance
Related Reading
Cases and Knowledge for This Industry
Carbide Sleeve With 176 Holes
A carbide sleeve of OD 268 mm x ID 228.6 mm x H 160 mm carrying 176 holes produced for oil field service equip…
Read MoreAPI V11 Valve Pair Supply
Tungsten carbide ball and seat valve pairs in the API V11 series produced for subsurface oil well pumps togeth…
Read MoreTungsten Carbide Grade Guide
How cobalt content and grain size move hardness against toughness and how to describe your application so a su…
Read MoreSinter-HIP Process Guide
The production route from WC powder through ball milling spray drying pressing Sinter-HIP and machining and wh…
Read MoreCarbide Compared With Tool Steel
Where cemented carbide is worth the extra cost against hardened tool steel and where a steel part remains the …
Read More
FAQ
Petroleum and Gas FAQ
Which carbide products do you recommend for petroleum and gas?
Mainly API V11 Ball and Seat, Carbide Sleeves, Carbide Cores and Seats, Carbide Tubes and Bushes. The right one depends on the geometry and the failure mode so send a drawing or photos of the worn part.
Can you match a part we currently buy elsewhere?
Yes if you send the drawing or a measured sample. We prepare a drawing for your approval before production and we do not copy from photographs alone.
What information helps you quote quickly for this sector?
The drawing the quantity the operating conditions and how the current part fails. Send it on WhatsApp to +86 187 7492 5813 or by email to [email protected].
Do you supply sample quantities first?
For critical applications a sample run before the production order is the honest way to confirm both the grade and the geometry. Ask for it when you enquire.
Next Step
Get a Carbide Solution for Petroleum and Gas
Send the drawing or photos of the worn part with measured dimensions. Our engineers reply with a direction you can evaluate.
Send a drawing or a sample photo on WhatsApp or by email. Files are reviewed by our production engineers, not by a form.