- Home
- Products
- Diamond Wire for Stone
- Diamond Wire Saw for Profiling
Diamond Wire Saw for Profiling
Profiling wire for shaped cuts in stone
Profiling asks the wire to follow a curve under tension without shedding beads, which is a bond and spacing question. Item IDs SA85GPP-SA90GPS cover 8.5-9.0 mm wire in both configurations.
What Diamond Wire Saw for Profiling Is For
The plant specification sheet describes this tool as for stone profiling with high efficiency, low noise, environment protection. That is exactly where it belongs, and where it stops.
The specification table lists 18 sizes, Item IDs SA85GPP to SA90MPS.
Inside Diamond Wire for Stone there are 5 items to choose between. This one is the profiling wire for shaped cuts in stone option — the comparison further down this page sets it against the others.
How It Is Built
Bond selected per enquiry
We do not ship a single general-purpose bond. Please inform your stone information, we will choose the best bonding for you.
Item ID series
Ordering runs on the SA85GPP to SA90MPS series, so repeat orders return the same specification.
Sizes beyond the standard list
Other sizes are available upon customer's request.
Export handling
Packed for export and shipped from Shangqiu, Henan. Give us your destination port with the enquiry.
Sizes and Item IDs
Taken from the plant specification sheets. Where a value is not published we say so rather than fill it in.
| Item ID | Diameter | Fixing type | Beads | |
|---|---|---|---|---|
| mm | Number(pcs/m) | Length(mm) | ||
| SA85GPP | 8.5 | Plastic | 37-39 | 10 |
| SA85GPS | Plastic+Spring | 37-39 | 10 | |
| SA90GPP | 9.0 | Plastic | 37-39 | 10 |
| SA90GPS | Plastic+Spring | 37-39 | 10 |
| Granite hardness | Linear speed | Cutting speed | Service life |
|---|---|---|---|
| m/s | mm/min | m 2 /m | |
| Soft | 26-30 | 10-15 | 8-12 |
| Medium | 22-26 | 5-10 | 7-10 |
| Hard | 18-22 | 4-6 | 4-7 |
| Item ID | Diameter | Fixing type | Beads | |
|---|---|---|---|---|
| mm | Number(pcs/m) | Length(mm) | ||
| SA85MPP | 8.5 | Plastic | 33 | 10 |
| SA85MPS | Plastic+Spring | 33 | 10 | |
| SA90MPP | 9.0 | Plastic | 33 | 10 |
| SA90MPS | Plastic+Spring | 33 | 10 |
| Marble hardness | Linear speed | Cutting speed | Service life |
|---|---|---|---|
| m/s | mm/min | m 2 /m | |
| Soft | 30-40 | 20-35 | 35-50 |
| Medium | 27-35 | 15-25 | 25-40 |
| Hard | 26-30 | 10-18 | 20-30 |
- Product family
- Stone Processing
- Category
- Diamond Wire for Stone
- Bond
- Please inform your stone information, we will choose the best bonding for you.
- Country of manufacture
- China (Shangqiu, Henan)
- Private label
- Laser marking on the steel core available for OEM orders
Who It Is For
- Quarries cutting and squaring blocks
- Stone plants running multi-wire slab saws
- Contractors profiling stone on site
Every one of these buyers gets the same first question from us: what material, what machine, what size.
The Problem It Solves
Wire cutting only pays when the bead spacing and bond match the stone and the machine.
Diamond Wire Saw for Profiling is the answer to that in the diamond wire for stone part of the range: profiling wire for shaped cuts in stone.
For stone profiling with high efficiency, low noise, environment protection.
Why This Version and Not Another
Four wire families for quarry squaring profiling and multi-cutting instead of one general wire
Applies across the diamond wire for stone series, including this item.
Rubber and spring configurations in the same diameter ladder
Part of how this category is built.
Loose beads available for re-stringing
Part of how this category is built.
Use Guide
Confirm the fit
Check diameter, bore and segment dimensions against the table above and against your machine.
Set the parameters
Start at the machine builder's figures for your material, then adjust feed until the cut runs quiet and the surface stays clean.
Keep it free-cutting
If the tool stops cutting and the face goes shiny, it has glazed. Dress it, then tell us — that means the bond should change.
Order by Item ID
Quote the Item ID on repeat orders so you get the same specification as last time.
Compared With the Rest of the Category
Diamond Wire for Stone holds 5 items in the programme. The difference between them is geometry and construction, not marketing.
- Diamond Beads for Stone — loose beads for re-stringing diamond wire
- Diamond Wire Saw for Multi-cutting — multi-wire slab cutting at low kerf loss
- Diamond Wire Saw for Quarry — quarry wire for primary block extraction
- Diamond Wire Saw for Squaring — squaring wire for trimming blocks to size
Diamond Wire Saw for Profiling — Questions We Get Asked
What sizes does Diamond Wire Saw for Profiling come in
The standard programme lists 18 sizes on this page, Item IDs SA85GPP to SA90MPS. Other sizes are available upon customer's request.
Which bond will you supply for my material
The bond is set per enquiry rather than per catalogue number. Please inform your stone information, we will choose the best bonding for you.
What do you need to quote Diamond Wire Saw for Profiling
The material you process, the machine and its power, the size and bore you need, and the quantity. With those four we quote a specification rather than a guess.
What is the lead time and minimum order for Diamond Wire Saw for Profiling
Lead time and minimum order depend on whether the size is in the standard programme or needs a production batch. Ask the sales office for this item — we do not publish a single figure that would be wrong half the time. (TBC)
Others in the Same Part of the Range
Diamond Beads for Stone
Loose beads for re-stringing diamond wire
View specifications →
Diamond Wire Saw for Multi-cutting
Multi-wire slab cutting at low kerf loss
View specifications →
Diamond Wire Saw for Quarry
Quarry wire for primary block extraction
View specifications →
Diamond Wire Saw for Squaring
Squaring wire for trimming blocks to size
View specifications →Related Technical Guides
Get a quote for Diamond Wire Saw for Profiling
Send the material, machine and size. You will get a specification and a price, not a catalogue page.