Backup Camera
Heavy Duty Bracket Camera for Trucks Trailers and Machines
- Bracket mounting means no hole saw work on the vehicle body
- Moulded sun shield keeps rain and low angle sun off the lens
- Infrared LEDs give a usable picture in an unlit yard
Product Overview
Backup Camera at a Glance
This is the workhorse of the range: a shielded bracket camera made for the back of a truck body, a trailer door or a piece of site machinery. The housing carries a moulded sun shield over the lens and a ring of infrared LEDs, and the bracket lets the installer set the down angle once and lock it.
It is the format most fleet workshops ask for because it mounts to sheet metal or a cross member without a hole saw, and because the shield keeps rain and low sun off the lens where a bare barrel camera would wash out.
Key Benefits
Why Buyers Specify This Model
Bracket mounting means no hole saw work on the vehicle body
Moulded sun shield keeps rain and low angle sun off the lens
Infrared LEDs give a usable picture in an unlit yard
Angle is set once at fitting and stays where it is put
Application and Fit
Where It Is Used and Who It Is For
Application Scenarios
- Rigid trucks and box bodies
- Trailers and semi trailers
- Site machinery and agricultural equipment
- Refuse and utility vehicles
Who It Is For
- Fleet workshops
- Truck body builders
- Machinery dealers
- Accessory distributors
Problems It Solves
- Blind zone behind a long body
- Cameras that wash out in low sun
- Nothing visible when reversing in an unlit yard
- Bodywork that cannot be drilled
Technical Features
Technical Features
- Housing designed around a specific mounting position rather than a universal bracket
- Sealed construction, with the sealed camera range certified to IP68
- Supplied with the termination your head end needs, 4 pin aviation or RCA
- Cable length made to the routed distance on your vehicle, not a fixed standard length
- Housing colour, labelling and packaging available under your own brand
Specifications
Configuration and Specification Sheet
| Housing | Shielded metal body with moulded sun visor |
|---|---|
| Mounting | Adjustable bracket, surface mounted |
| Night vision | Infrared LED array around the lens |
| Cable | Rear exit, single cable |
Full electrical specification is issued per order. Sensor, resolution, lens angle, supply voltage, cable length and connector on this model are confirmed against your vehicle and your head end before production, because they are the parameters most often changed on an OEM order. Ask for the specification sheet and we will send it with the quotation.
Materials
Materials and Construction
Camera bodies in the range use metal and moulded composite housings depending on the mounting position, with a compressed gasket at the lens cover and a strain relieved cable gland at the tail. The sealed camera range is certified to IP68. Exact housing material for a given model is confirmed on the specification sheet before an order is placed.
Manufacturing Process
How It Is Made
Manufactured at our Guangzhou facility. Specification is fixed first, a physical sample is built and approved, components are sourced against the approved sample, the unit is assembled and sealed, then function checked and packed. Production is carried out strictly in accordance with the ISO9001 standard.
Quality Control
Quality Control Steps
- Incoming component check against the approved sample specification
- Assembly with gasket compression and cable gland made off on sealed housings
- Power up and image output check on every unit
- Infrared or assist lamp function check where the model has them
- Final visual and packaging check before carton packing
Certifications
Certifications Held on the Range
- ISO9001
- IP68
- CE
- FCC
- RoHS
- E-mark
Certificates apply to specific models and test reports. Ask for the certificate covering the exact model you are ordering rather than a general company document.
Customization
Customization Options
- Housing colour and surface finish
- Cable length made to the routed distance on your vehicle
- Connector type, 4 pin aviation or RCA, or to your drawing
- Label and silkscreen artwork under your own brand
- Retail box, inner packing and printed manual
- Carton marking and quantity per carton
Comparison
Compared With Other Products in the Range
| Backup Camera | Side Camera | Dome Camera | |
|---|---|---|---|
| Range | Vehicle Cameras | Vehicle Cameras | Vehicle Cameras |
| Built for | Heavy Duty Bracket Camera for Trucks Trailers and Machines | Wedge Housing Camera for Corner and Kerb Side Views | Ceiling Mount Dome With a 4 Pin Aviation Connector |
| Primary application | Rigid trucks and box bodies | Van and truck near sides | Bus and coach saloons |
| Main advantage | Bracket mounting means no hole saw work on the vehicle body | Covers the near side blind zone mirrors cannot reach | Screw locked 4 pin connector will not vibrate loose |
If you are unsure which of these fits your vehicle, send a photo of the mounting position and we will tell you which one to order.
Use Guide
Installation and Use Guide
A short fitting sequence. The full installation guide is available in the Download Center.
- 01
Confirm the Mounting Position
Hold the backup camera where it will be fitted and confirm the view or the screen position works before anything is drilled or fixed.
- 02
Check the Cable Reaches
Route the full cable from the unit to the head end and confirm it reaches with slack to spare, away from exhaust heat and moving parts.
- 03
Fix the Unit
Fit the bracket, collar or stand and seal any panel entry point. Leave a drip loop below an exterior entry so water runs away from the hole.
- 04
Connect Power and Video
Make the video and power connections in dry positions, supported so no joint carries the weight of the loom.
- 05
Set and Test
Power up, set the angle or the screen position from the driver's seat, and test again after dark and with the vehicle wet.
Knowledge
Related Guides
Downloads
Documents for This Product
Explore
Related Products
Vehicle CamerasSide CameraWedge Housing Camera for Corner and Kerb Side Views
View Product
Vehicle CamerasDome CameraCeiling Mount Dome With a 4 Pin Aviation Connector
View Product
Vehicle CamerasCar Backup CameraFlush Barrel Camera for a Clean Bumper Installation
View Product
Vehicle Monitors7 Inch Vehicle Monitor7 Inch Commercial Vehicle Display for Multi Camera Systems
View ProductFAQ
Backup Camera FAQ
What is the MOQ on the Backup Camera?
MOQ varies by model and by how much customisation the order carries. Send your quantity and destination market and we will confirm the MOQ in writing with the quotation.
Can this product be supplied under our own brand?
Yes. OEM and ODM service covers housing colour, cable and connector specification, label artwork, printed manual and retail packaging.
Which certificates cover this product?
Our product range holds IP68, CE, FCC, RoHS and E-mark certificates, and production is carried out strictly in accordance with the ISO9001 standard. Ask for the certificate covering this exact model before shipping.
How is it packed and shipped?
Carton packing, with retail boxes and inner packing where the order calls for them. Shipment by express, air, land or sea, with sea shipments loading at Shenzhen or Guangzhou.
Can I get a sample before placing a production order?
Yes. Samples are dispatched for physical approval before production. Ask for a sample through WhatsApp or email and we will confirm the cost and the lead time.
Do you have a CAD file or drawing available?
CAD files are not published for download. Request a CAD file or a dimensioned drawing through WhatsApp or email and we will send it directly once the application is confirmed.
Next Step
Get a Quotation on the Backup Camera
Send your quantity, destination market and any customisation you need. We will come back with price, MOQ and lead time.