Mini Rear View Camera
Lip Mount Bullet Camera for Tight Rear Panels
- Fits a panel lip where a flat bracket has nothing to sit on
- Angle can be trimmed after the bracket is fixed
- Smallest surface mounted body in the range
Product Overview
Mini Rear View Camera at a Glance
A bullet style camera on a slim lip bracket, made for the panel edge above a number plate or a boot lid lip where there is no flat surface to mount to. The body swivels in the bracket so the down angle can be trimmed after the bracket is screwed down.
It is the smallest surface mounted camera we build and the usual answer when a customer wants a reversing view on a vehicle where nothing else will physically fit.
Key Benefits
Why Buyers Specify This Model
Fits a panel lip where a flat bracket has nothing to sit on
Angle can be trimmed after the bracket is fixed
Smallest surface mounted body in the range
Discreet on a passenger car or a small van
Application and Fit
Where It Is Used and Who It Is For
Application Scenarios
- Boot lid lips
- Number plate surrounds
- Small van rear doors
- Motorhomes
Who It Is For
- Installers
- Accessory retailers
- Workshops
- Distributors
Problems It Solves
- No flat mounting surface at the rear
- Bracket cameras that look oversized on a small car
- Angle that cannot be corrected once the bracket is fixed
- Limited clearance around the plate
Technical Features
Technical Features
- Housing designed around a specific mounting position rather than a universal bracket
- Sealed construction, with the sealed camera range certified to IP68
- Supplied with the termination your head end needs, 4 pin aviation or RCA
- Cable length made to the routed distance on your vehicle, not a fixed standard length
- Housing colour, labelling and packaging available under your own brand
Specifications
Configuration and Specification Sheet
| Housing | Small bullet body |
|---|---|
| Mounting | Slim lip bracket, swivel adjustment |
| Adjustment | Body rotates in the bracket after fitting |
| Cable | Rear exit, single cable |
Full electrical specification is issued per order. Sensor, resolution, lens angle, supply voltage, cable length and connector on this model are confirmed against your vehicle and your head end before production, because they are the parameters most often changed on an OEM order. Ask for the specification sheet and we will send it with the quotation.
Materials
Materials and Construction
Camera bodies in the range use metal and moulded composite housings depending on the mounting position, with a compressed gasket at the lens cover and a strain relieved cable gland at the tail. The sealed camera range is certified to IP68. Exact housing material for a given model is confirmed on the specification sheet before an order is placed.
Manufacturing Process
How It Is Made
Manufactured at our Guangzhou facility. Specification is fixed first, a physical sample is built and approved, components are sourced against the approved sample, the unit is assembled and sealed, then function checked and packed. Production is carried out strictly in accordance with the ISO9001 standard.
Quality Control
Quality Control Steps
- Incoming component check against the approved sample specification
- Assembly with gasket compression and cable gland made off on sealed housings
- Power up and image output check on every unit
- Infrared or assist lamp function check where the model has them
- Final visual and packaging check before carton packing
Certifications
Certifications Held on the Range
- ISO9001
- IP68
- CE
- FCC
- RoHS
- E-mark
Certificates apply to specific models and test reports. Ask for the certificate covering the exact model you are ordering rather than a general company document.
Customization
Customization Options
- Housing colour and surface finish
- Cable length made to the routed distance on your vehicle
- Connector type, 4 pin aviation or RCA, or to your drawing
- Label and silkscreen artwork under your own brand
- Retail box, inner packing and printed manual
- Carton marking and quantity per carton
Comparison
Compared With Other Products in the Range
| Mini Rear View Camera | Mini Backup Camera | Car Backup Camera | |
|---|---|---|---|
| Range | Vehicle Cameras | Vehicle Cameras | Vehicle Cameras |
| Built for | Lip Mount Bullet Camera for Tight Rear Panels | Compact Bracket Camera With Four Assist Lamps | Flush Barrel Camera for a Clean Bumper Installation |
| Primary application | Boot lid lips | Passenger cars | Passenger car bumpers |
| Main advantage | Fits a panel lip where a flat bracket has nothing to sit on | Small enough for a number plate lip or a tailgate recess | Almost invisible once fitted, only the lens bezel is on show |
If you are unsure which of these fits your vehicle, send a photo of the mounting position and we will tell you which one to order.
Use Guide
Installation and Use Guide
A short fitting sequence. The full installation guide is available in the Download Center.
- 01
Confirm the Mounting Position
Hold the mini rear view camera where it will be fitted and confirm the view or the screen position works before anything is drilled or fixed.
- 02
Check the Cable Reaches
Route the full cable from the unit to the head end and confirm it reaches with slack to spare, away from exhaust heat and moving parts.
- 03
Fix the Unit
Fit the bracket, collar or stand and seal any panel entry point. Leave a drip loop below an exterior entry so water runs away from the hole.
- 04
Connect Power and Video
Make the video and power connections in dry positions, supported so no joint carries the weight of the loom.
- 05
Set and Test
Power up, set the angle or the screen position from the driver's seat, and test again after dark and with the vehicle wet.
Applications
Industries This Product Serves
Knowledge
Related Guides
Downloads
Documents for This Product
Explore
Related Products
Vehicle CamerasMini Backup CameraCompact Bracket Camera With Four Assist Lamps
View Product
Vehicle CamerasCar Backup CameraFlush Barrel Camera for a Clean Bumper Installation
View Product
Vehicle Monitors7 Inch Mirror MonitorClip on Mirror Screen That Uses No Dash Space
View Product
Vehicle CamerasMini Dome CameraCompact Interior Dome With RCA and DC Leads
View ProductFAQ
Mini Rear View Camera FAQ
What is the MOQ on the Mini Rear View Camera?
MOQ varies by model and by how much customisation the order carries. Send your quantity and destination market and we will confirm the MOQ in writing with the quotation.
Can this product be supplied under our own brand?
Yes. OEM and ODM service covers housing colour, cable and connector specification, label artwork, printed manual and retail packaging.
Which certificates cover this product?
Our product range holds IP68, CE, FCC, RoHS and E-mark certificates, and production is carried out strictly in accordance with the ISO9001 standard. Ask for the certificate covering this exact model before shipping.
How is it packed and shipped?
Carton packing, with retail boxes and inner packing where the order calls for them. Shipment by express, air, land or sea, with sea shipments loading at Shenzhen or Guangzhou.
Can I get a sample before placing a production order?
Yes. Samples are dispatched for physical approval before production. Ask for a sample through WhatsApp or email and we will confirm the cost and the lead time.
Do you have a CAD file or drawing available?
CAD files are not published for download. Request a CAD file or a dimensioned drawing through WhatsApp or email and we will send it directly once the application is confirmed.
Next Step
Get a Quotation on the Mini Rear View Camera
Send your quantity, destination market and any customisation you need. We will come back with price, MOQ and lead time.