Feel The Life With Light · LED manufacturer since April 2010
C&R Group
Products
Industries
Solutions
Resources

Request A Quote

LED Strip Lights

SMD5060 30 LEDs/m IP68 LED Strip Light

Part number CRWS-101-30S

This flexible LED strip is made for cove, cabinet, signage and display lighting cut to length on site, and SMD5060 30 LEDs/m IP68 LED Strip Light is the model that covers it. It is specified with 120 degree. beam angle. Consistent LED pitch and PCB width is what makes a repeat order work. It is catalogued as CRWS-101-30S.

Beam Angle
120 degree.
Key Benefits

What This Model Gives You

120 degree. beam angle

Beam angle is specified as part of the product rather than left as a surprise on site.

Against rigid LED bar lighting

Follows curves and corners that a rigid bar cannot.

Against a lower IP grade strip used outdoors

The sealed grades are specified for the exposure they will actually see.

Against a boxed retail strip kit

Bulk strip lets the installer cut to length rather than work around a fixed kit.

Specifications

Technical Data For SMD5060 30 LEDs/m IP68 LED Strip Light

Every figure below is taken from the manufacturer's specification for this model. Where a value is not listed it is not published, and we will confirm it against current production before you order.

Item NoCRWS-101-30S
PCB Colorwhite or yellow board.
Beam Angle120 degree.
Lift Span50000 ~ 80000 hours.
Available ColorWhite, Warm White, Red, Green, Blue, Yellow, RGB
Technical Features

How It Is Built

  • 2. Flexible strip, cuttable every 3 lamps.
  • 7. Light fading aftering 1000 hours continue work: white color less than 20%, other colors less than 5%.
  • Solid silicon waterproof IP68(with silicon cover on the back and silicon gel filled from the top).
Who It Is For

Buyers This Model Suits

  • Display and exhibition builders
  • Contractors doing cove and architectural lighting
  • Sign makers, cabinet makers and shopfitters
  • Distributors supplying electrical installers

Application Scenarios

  • Signage and channel letter illumination
  • Camping, van and vehicle interior lighting
  • Retail kit sales through hardware and lifestyle stores
  • Cove, cabinet and display lighting in retail interiors
Problems It Solves

Objections This Model Removes

01

Strip is bought without the driver and controller it needs

02

Strip is cut in the wrong place and a whole section stops working

03

Waterproof grade is quoted vaguely and the strip fails outdoors

04

A repeat order arrives with a different LED pitch and does not match

Manufacturing Process

How This Product Is Made

Production runs at our Shenzhen plant, Shenzhen Chiclits Technology Co., Ltd..

Flexible PCB preparation and solder paste printing

SMD LED placement and reflow along the strip

Silicone or resin encapsulation to the specified IP grade

Reel winding, electrical test and packing

Quality Control

What Gets Checked

  • Encapsulation integrity check against the IP grade
  • LED pitch and PCB width verification
  • Colour consistency across the production batch
  • Continuity and brightness test along the full reel
Customisation

What You Can Change

  • IP67 or IP68 waterproof grade
  • LED density selected from the published options
  • PCB colour specified white or yellow
  • Reel length and connector configuration

Certification

Our LED bulb line holds CE (LVD) and RoHS certificates issued by Shenzhen BST Technology, with the numbers published on our Trust page. Ask us in writing for the certification position on this specific model before you quote it into a regulated market - we will tell you what is held and what is not.

See our certificates

Comparison

How It Compares With The Alternatives

Compared withWhat changes
A boxed retail strip kitBulk strip lets the installer cut to length rather than work around a fixed kit
Rigid LED bar lightingFollows curves and corners that a rigid bar cannot
A lower IP grade strip used outdoorsThe sealed grades are specified for the exposure they will actually see
Use Guide

Getting It Right On Site

01

Cut only at the marked intervals stated in the specification

02

Size the power supply for the total wattage of the run plus headroom

03

Feed long runs from both ends to avoid voltage drop along the strip

04

Clean and dry the surface before applying adhesive-backed strip

Questions Buyers Ask

SMD5060 30 LEDs/m IP68 LED Strip Light Questions

What beam angle is this model?

120 degree.. Beam angle is a separate part number in this range, so order the angle you need rather than adjusting on site.

Where can this strip be cut?

At the interval stated in the specification on this page. Cutting anywhere else will kill the section.

What is the difference between the IP67 and IP68 versions?

Both are sealed. IP67 is rated for temporary immersion and IP68 for continuous immersion. They are separate part numbers.

Can I run this from any 12V supply?

Size the supply for the total wattage of the run with headroom. Send us the run length and we will specify the driver.

What comes in a strip light kit?

Strip, an IR controller and remote in 14-key, 24-key or 44-key form, and retail packaging in blister or colour box. The exact contents are listed on each kit page.

What is the minimum order quantity and lead time for this model?

Both depend on the configuration, the packaging and the quantity, and neither is published as a blanket figure. Send us the model and quantity by email and we will confirm in writing.

Get Pricing For SMD5060 30 LEDs/m IP68 LED Strip Light

Send the quantity and destination market. We reply with pricing, packaging options, lead time and a written position on certification.