103 Wall Bracket
103 Wall Bracket is a two-leg pressed steel shelf bracket in the London profile, folded from strip steel and punched with six fixing holes so the load is shared across the stud rather than a single screw. It is the volume line for closet, garage and shed shelving, and it is sized to standard lumber widths so retail buyers can shelve it against timber without a conversion table. This model is listed in 6 sizes, from 80 x 125 x 0.8 mm to 230 x 350 x 1.0 mm. Stock finishes are White, grey and black.
Available Sizes
- 80 x 125 x 0.8 mm
- 100 x 150 x 0.8 mm
- 140 x 200 x 0.8 mm
- 160 x 250 x 1.0 mm
- 200 x 300 x 1.0 mm
- 230 x 350 x 1.0 mm
What This Model Gives You
- Six screw holes per bracket spread the load across the stud face
- Leg lengths follow standard lumber widths so the shelf overhangs evenly
- Folded from one steel blank with no welded joint to fail
- Stacks flat in the carton which keeps carton count and freight low
How It Is Built
- Cold-formed from steel strip in a single press operation
- Punched fixing holes on both legs
- Powder coated or plated after forming
Application Scenarios
- Closet and wardrobe shelving
- Garage and shed storage racks
- Utility room and laundry shelving
- Retail backroom shelving
Who It Is For
- DIY and hardware retail chains buying shelving hardware in pack quantities
- Closet and storage system assemblers
- Builders merchants supplying garage and shed fit-outs
- Private label programmes that need one bracket profile in many lengths
Problems It Solves
- Single-screw brackets pull out of plasterboard under load
- Mixed bracket profiles across a range make retail packaging inconsistent
- Imported brackets often arrive in metric sizes that do not match local shelf boards
103 Wall Bracket Specification
Every figure below comes from our own product data. Where a value is not published we leave the row out rather than estimate it.
| Product Code | 103 |
|---|---|
| Product Type | London Bracket |
| Sizes | 80 x 125 x 0.8 mm · 100 x 150 x 0.8 mm · 140 x 200 x 0.8 mm · 160 x 250 x 1.0 mm · 200 x 300 x 1.0 mm · 230 x 350 x 1.0 mm |
| Number of Sizes | 6 |
| Material Thickness | 0.8 - 1.0 mm |
| Material | Cold rolled steel strip |
| Finish | White, grey and black |
| Customization | OEM and ODM to drawing or sample; private label and own label |
| Minimum Order | Very small minimum order quantity, negotiable |
| Shipping Terms | EX Works, FOB, CIF, DDU or DDP by sea, rail or courier |
Materials
- Cold rolled steel strip
Manufacturing Process
- Blanking
- Punching
- Press forming
- Deburring
- Surface finishing
- Inspection
- Packing
The Checks This Part Passes
- Material inspection, with failed material returned rather than run
- First lot sample inspection before mass production is released
- Random inspection during mass production covering 30 to 40 percent of output
- Finished goods inspection against the lot
- Mass production stopped at or above 10 percent defective; repair or rework below it
Changing It to Suit You
- OEM and ODM production to your drawing or sample
- Private label or our own label
- Sizes between the listed steps run to order
- Finish changed to your specification, applied after forming
- Retail packing with mounting screws on request
How It Compares
Compared With Cast or ornamental brackets
A pressed London bracket carries the same shelf load at a fraction of the weight and unit cost, which matters when the bracket is sold in pairs at a retail price point.
Compared With Plastic shelf supports
Steel does not creep under a sustained load and does not become brittle in an unheated garage or shed.
Use Guide
- Mark the stud centres before drilling; the bracket is designed to land on a stud, not on plasterboard alone.
- Use the longer leg vertically against the wall and the shorter leg under the shelf.
- Fill every punched hole. The stated holding pattern assumes all six screws are used.
- Keep the shelf board flush with the end of the horizontal leg so the load sits inside the bracket, not past it.
Others in This Family
Further Reading
How to Choose a Shelf Bracket Size and Thickness
Bracket sizes are quoted as wall leg x shelf leg x material thickness. This guide explains how to read that notation, how to...
Shelf Bracket Finishes Compared White Grey Black Zinc and Galvanized
Powder coat, zinc plating, brass and nickel plating and hot dip galvanizing all appear across our range. Each one fails in a...
Questions About the 103 Wall Bracket
What shelf depth should I order for a 250 mm board?
Order the bracket whose horizontal leg is equal to or slightly shorter than the board depth, so the board covers the bracket. For a 250 mm board the 200 x 250 mm size is the usual choice.
Can you supply the bracket in our own colour?
Yes. White, grey and black are standard. Other RAL colours are run to order; the colour is applied after forming, so it does not change the tooling.
Are screws included?
Screws are not included as standard on this line. They can be packed with the bracket as a retail set on request.
Which sizes of the 103 Wall Bracket are available?
This model is listed in 6 sizes: 80 x 125 x 0.8 mm, 100 x 150 x 0.8 mm, 140 x 200 x 0.8 mm, 160 x 250 x 1.0 mm, 200 x 300 x 1.0 mm, 230 x 350 x 1.0 mm. Sizes between the listed steps are run to order.
Can I get a sample of the 103 Wall Bracket before ordering?
Yes. Samples under US$20 in value are free if you have a DHL, TNT, UPS or FedEx account or agree to cover the freight. Above US$20 we ask you to cover the sample and freight cost, and we ship on receipt of payment.
What payment terms do you accept?
We accept T/T, D/P, L/C, Western Union and PayPal.
Ready to Price the 103 Wall Bracket
Tell us the size, the finish and the quantity. If you need a size that is not listed, say so: sizes between the listed steps are run to order.