D60041
Manufactured by Wanhao Industry in Zhangzhou, China, for export programmes. Colour and size customisation are open where the specification table below says so.
What This Model Is
D60041 sits in the coat rack and shoe rack section of the Wanhao catalogue and is built to order for export programmes. Construction follows the same route as the rest of the range: steel parts cut, formed and coated in house, then matched to the panel, glass or upholstered components before packing. It is quoted mainly to h who need one factory to cover a whole product family.
Every model in the catalogue is quoted with its own carton drawing and loading plan. What the factory can confirm today is in the specification table below; what it cannot is marked TBC rather than filled in with a plausible number.
Key Benefits
Flat pack with simple assembly
Three to six parts on most models.
A family that merchandises together
Shoe bench, coat stand and rail in the same finish.
Bamboo and fabric options
Warmer materials at the same frame cost.
What This Model Is Specified Against
The problems below are the ones that turn a coat rack and shoe rack order into a customer-service case. Each one is a build decision on this model.
- Coat stands that tip when loaded on one sideBase weight and foot spread are specified per model so a loaded stand stays upright.
- Rust on racks that meet wet shoesPowder coating over prepared steel is the standard build; the coating spec per model is confirmed at quotation.
- Fabric seats that pull off the frameSeat fixing and fabric tension are set on the line and checked before packing.
Where It Gets Used
Small apartments
Vertical storage where floor area is scarce.
Entryways and mudrooms
Shoes, coats and bags at the door.
Bedrooms
Open clothes rails used as a wardrobe substitute.
Retail and staff areas
Uniform and outerwear storage.
Buyers Who Specify It
- Contract buyers fitting out staff changing areas
- E-commerce sellers in the entryway category
- Home-organisation brands and importers
- Discount and variety retail buyers
Construction
- Powder-coated steel tube frames
- Fabric, MDF or bamboo seats and shelves
- Shoe racks in 2 to 5 tiers
- Clothes rails with hanging bar and lower shelf
- Non-marking foot pads
What We Can Confirm
| Model code | D60041 |
|---|---|
| Product name | D60041 |
| Category | Coat Rack and Shoe Rack |
| Minimum order quantity | TBC — quoted per model |
| Frame material | Powder-coated steel; grade and gauge confirmed at quotation |
| Finished dimensions | TBC — confirmed on the specification sheet |
| Carton size and loading quantity | TBC — confirmed on the carton drawing |
| Net and gross weight | TBC — confirmed at quotation |
| Test reports and certificates | TBC — confirmed per destination market |
| Country of manufacture | China — Zhangzhou, Fujian |
TBC means the previous catalogue never published that value. It is confirmed in writing at quotation rather than estimated here.
What It Is Made Of
Wanhao works in powder-coated steel tube, cold-rolled steel sheet, MDF, melamine-faced board, tempered glass, bamboo, and upholstery fabric and PU. The exact build-up for this model is confirmed on the specification sheet at quotation — the old catalogue did not publish it, and guessing it here would not help you cost the product.
CustomisationWhat Can Be Changed
- Colour, where the specification table shows Color: Customized
- Size, where the specification table shows Size: Customized
- Carton artwork, barcodes and retail labels to your files
- Instruction sheet produced to your artwork and languages
- Buyer-specified variants developed against your drawing, with tooling stated in the quote
Where It Gets Checked
- Incoming steel, panel, glass and fabric checked against the model specification
- First piece off the line checked against the approved pre-production sample
- Frames checked flat and square before surface preparation
- Coating colour and coverage checked against the approved sample
- Hardware pack counted against the instruction sheet
- A unit assembled from the carton to confirm fit and instructions
- Carton, print and handling marks verified before sealing
- Pre-shipment inspection to the AQL agreed with the buyer
How This Model Is Produced
Material intake
Steel, panel, glass and fabric received against the model specification.
Cutting and forming
Tube and sheet cut, bent and pressed to the frame drawing.
Welding and assembly
Joints made where the drawing places them, then dressed.
Surface preparation
Parts prepared so the powder coating holds.
Powder coating
Coated on the line, colour matched to the approved sample.
Surface components
Panel, glass, bamboo or upholstered parts fitted and checked against the frame.
Packing
Packed to the signed carton drawing with the specified internal protection.
Inspection and loading
Sampled against the agreed AQL, then loaded to the agreed plan.
How It Compares
Against a lower-gauge import
A thinner-gauge equivalent will look identical in a photograph and fail at the joint under the same load. The gauge on D60041 is fixed per the drawing and held for the life of the order.
Against buying frame and surface from two suppliers
Splitting the frame and the surface across two factories means two QC standards and a fit problem nobody owns. D60041 is fabricated and fitted in one plant.
Assembly and Care
- Unpack on the carton itself so the finished surfaces never touch the floor.
- Check the parts against the parts list before you start; a missing fixing is easier to report before assembly than during it.
- Assemble on a flat surface and leave every fixing finger-tight until the last one is in place.
- Tighten in sequence, then stand the unit up and adjust the feet against the floor.
- Wipe coated surfaces with a damp cloth only; solvent cleaners will dull a powder-coated finish.
Other Models in This Range
Coat Rack and Shoe Rack
D60011
View model
Coat Rack and Shoe Rack
D60012
View model
Coat Rack and Shoe Rack
D60015
View model
Coat Rack and Shoe Rack
D60013
View model Buyer programmes
E-Commerce and Flat-Pack Retail — Single-carton products that survive a parcel network
Capabilities
Export Packing and Logistics — 120 countries of shipping history behind the packing drawing
Quality Control Programme — Checks placed where the failures actually happen
OEM and ODM Development — From a reference photo to an approved sample to a repeatable production run
Related guides
How to Source Steel Frame Furniture From China Without Getting Burned
The eight questions that separate a factory that will still be producing your model in year three from one that will not.
Powder Coating Explained for Furniture Buyers
What powder coating does, what it does not do, and the three questions to ask before you call a product outdoor-suitable.
Questions About This Model
Can you produce D60041 in a different colour?
Colour customisation is available on this model where the specification table shows Color: Customized. Send a RAL reference or a physical sample and it is confirmed on a pre-production sample.
How is D60041 packed for export?
Packing is fixed on a carton drawing agreed before production. Carton size, board grade, internal protection and the container loading plan are confirmed in writing for this model.
Can the rack be made wider?
Yes, on models marked Size: Customized. A width change affects the bar span and is confirmed on a sample.
Do these need tools to assemble?
Most models assemble with the supplied Allen key. The instruction sheet is produced per model.
Are shoe bench seats padded?
Padded and unpadded versions both exist. The photo on each product page shows the version we make.
Quote D60041
Send the quantity and the destination market. Price, MOQ, carton size, loading quantity and the customisation options come back in one reply.