Real Work LED Lights
The SLL-0702-12-M is a 3 inch round LED work light designed for consistent illumination on machines that operate in harsh conditions. It delivers 960 effective lumens with a wide flood beam pattern, ensuring visibility across the immediate work zone without hot spots. The die-cast aluminium housing with durable UV polyester powder coating resists corrosion, while the shatterproof polycarbonate lens and stainless steel bracket maintain integrity under vibration and impact. Dual auto-select 12/24V DC operation allows one part number to serve both 12V and 24V fleets, reducing SKU complexity.
- 960 effective lumens spread evenly across the work area with a wide flood beam, avoiding dark edges around the machine
- Dual auto-select 12/24V DC input means the same part number works on 12V and 24V systems, simplifying inventory
- IP68 sealing and a shatterproof polycarbonate lens keep the light operational after exposure to water, dust, and impact
- Overvoltage and overheat protection prevent failure during electrical surges or prolonged high-load operation
- 50000 hour lifespan reduces replacement frequency on machines that run multiple shifts
Where This Lamp Is Used
- Side and rear work lighting on utility trailers and service trucks operating at night
- Cab roof and hood lighting on forestry vehicles and logging trucks in low-light conditions
- Auxiliary lighting on small construction equipment where space is limited
- Loading and unloading zone illumination on delivery vans and cargo trucks
- Fleet maintenance lighting on service vehicles where vibration and weather exposure are constant
Who It Is For
- Distributors of vehicle lighting needing one part number to cover both 12V and 24V systems
- Fleet operators replacing halogen work lights that fail under vibration or after a few wash cycles
- Machinery OEMs fitting work lights on production lines with consistent mounting patterns
- 4x4 accessory brands building a private label work light range with low SKU count
- Equipment dealers fitting lights on trailers and small utility vehicles where space is tight
Problems It Solves
- Halogen work lights burn out quickly under vibration and draw excessive current from the vehicle’s electrical system
- Cheap plastic lenses crack or fog up after repeated exposure to rain, pressure washing, or UV light
- Non-IP68 sealed lights fail after a few wash cycles due to water ingress through the cable entry
- Single-voltage lights require two SKUs for 12V and 24V fleets, increasing inventory and ordering complexity
- Painted mild steel brackets rust within months on machines exposed to daily washing or salt
Technical Features
- Twelve 1W Osram LEDs with a real power draw of 12W and a theoretical lumen output of 1080 lm
- Wide flood beam pattern with effective lumens spread across the immediate work zone
- Shatterproof polycarbonate lens with anti-UV and anti-scratch properties
- Die-cast aluminium housing with durable UV polyester powder coating
- Dual auto-select 12/24V DC input with overvoltage and overheat protection
- Operating temperature range of -40 to +85 degrees Celsius
- IP68 sealing for complete protection against water and dust ingress
- Bare wire lead of 40cm as standard with no connector included
Technical Specification
Values taken from the original factory specification for this model. Fields the factory sheet does not state are left out rather than estimated.
| Part Number | SLL-0702-12-M |
|---|---|
| Power | 12W |
| LED | 12 pcs x 1W Osram |
| Effective Lumen | 960 lm |
| Beam Pattern | Wide Flood |
| Colour Temperature | 6000K |
| Operating Voltage | 9–32V DC |
| Operating Temperature | -40 to +85 degrees Celsius |
| Housing Material | Die-cast aluminium with UV polyester powder coating |
| Lens Material | Shatterproof polycarbonate |
| Waterproof Rating | IP68 |
| Electrical Connection | Bare wire 40cm, no connector included |
| Protection | Overvoltage and overheat protection |
Materials Used
- Die-cast aluminium housing with UV polyester powder coating
- Shatterproof polycarbonate lens with anti-UV and anti-scratch treatment
- Silicone rubber gasket and sealed cable entry
- Bare copper wire lead with PVC insulation
How This Lamp Is Built
Die casting of the aluminium housing and heat sink
Powder coating with UV polyester finish
LED board assembly with 12 x 1W Osram emitters
Lens bonding and gasket sealing
Quality Control on This Model
- Photometric output verified in an integrating sphere
- Sealing verified against the IP68 rating before shipment
- Vibration testing on a vibration test machine to simulate machine-mounted service
- Salt spray corrosion testing on housing coating and stainless bracket
- High and low temperature alternating humidity testing across the -40 to +85 degrees Celsius range
Customisation Options
- Deutsch connector instead of the standard bare wire lead
- Alternative cable length to match a specific machine harness
- Private label logo on the housing and printed carton
- Spot beam optics in place of the standard flood pattern
- Mixed cartons combining this lamp with other SUNLITEC models for trial orders
How It Compares With the Alternatives
| Halogen work lamp of similar output | Draws 12W against roughly 30W for halogen and survives vibration that destroys a filament |
|---|---|
| Round 3.5 inch 16W work light | Smaller footprint fits tight spaces but lower output; same mounting pattern allows direct replacement |
| Spot beam version of the same lamp | Flood covers the near work area evenly while spot reaches further ahead but leaves the machine edges dark |
| Larger 4 inch 24W work light | Higher output but requires more space; this model fits where a larger body will not clear |
How to Fit and Use It
- Wire through a fused feed sized for 12W at 12V or 24V and keep the cable entry pointing downward
- Leave a drip loop in the 40cm lead so water runs away from the gland rather than into it
- Aim the flood beam at the immediate work zone close to the machine and use a spot lamp separately for distance
- Clean the PC lens with water and a soft cloth only, since solvents will degrade the anti-UV coating
Questions About This Model
Can I order a sample before placing a bulk order
Yes. Sample orders are welcome and mixed samples of different models in one shipment are accepted.
What is the lead time
Sample orders normally take around 3 to 7 working days. Bulk lead time depends on the model and the quantity ordered.
Do you have a minimum order quantity
There is an MOQ for standard orders, but smaller orders are also accepted, which suits distributors testing a new model.
How is the lamp shipped
Samples usually go by DHL, UPS, FedEx or TNT in around 4 to 7 days. Bulk orders ship by air in about 7 to 15 days or by sea in about 15 to 30 days.
Will this lamp work on both 12V and 24V machines
Yes. The operating range is 9 to 32V DC, so the same part number can be fitted to 12V and 24V vehicles.
Can you supply the lamp with our own brand
Yes. OEM and ODM service is available, including a private label logo on the housing and printed cartons.
Is it approved for road going machines
The lamp is IP68 sealed and carries overvoltage and overheat protection. It is not listed as ECE R10 approved, so verify local road compliance requirements.
Get a Price on Real Work LED Lights
Send the quantity, the destination port and any branding requirement. You will get pricing, packing data and the production lead time.