Lovsun IP65 Wall-mounted 5kWh 10kWh Lithium Battery
5-10 kWh
Lovsun IP65 Wall-mounted 5kWh 10kWh Lithium Battery gives a home solar system 5-10 kWh of usable LiFePO4 storage in a wall-hung enclosure, so an installer can add storage in an existing plant room without floor space or a battery rack.
What This Product Changes On Your Project
- Standard CAN and RS485 communication for inverter handshake, rather than a closed protocol that locks the buyer to one brand
- Usable depth of discharge that does not have to be derated the way lead-acid does
- No electrolyte maintenance, no equalisation charging and no ventilation requirement
- LiFePO4 chemistry - a flatter thermal profile and a longer cycle life than NMC at the same usable energy
- Integrated BMS with cell balancing, over-current, over-temperature and short-circuit protection
Application Scenarios
- Marine, RV and mobile installations replacing lead-acid banks
- Residential solar self-consumption, storing midday PV for the evening load
- Backup supply for homes and small offices on an unstable grid
- Telecom and monitoring cabinets where a site visit is expensive
- Off-grid cabins, farms and workshops running entirely on PV and storage
Who It Is For
- Telecom and infrastructure operators replacing lead-acid at remote sites
- Off-grid property owners sizing a standalone power system
- Solar installers specifying residential and light commercial storage
- Distributors and wholesalers stocking storage batteries for an installer base
Problems It Solves
- Closed inverter-battery protocols that force a whole-system replacement to change one component
- Lead-acid banks that have to be oversized because only part of the capacity is usable
- Replacement cycles every few years and the disposal cost that comes with them
- Solar output exported at a low feed-in tariff and bought back at a high retail one
Technical Features
- Parallel connection of multiple units to build capacity in steps
- Enclosure and terminal layout designed for a single-installer fit
- State-of-charge indication at the unit, not only through the inverter app
- LiFePO4 cells with an integrated BMS handling balancing and protection
- Over-voltage, under-voltage, over-current, over-temperature and short-circuit protection
Published Specification Data
These figures come from the manufacturer datasheet for this model. Where a value you need is not listed, ask for the full datasheet rather than assuming a typical figure.
| Energy capacity | 5-10 kWh |
|---|---|
| Ingress protection | IP65 |
| Brand | Lovsun |
| Nominal voltage | 51.2V |
| Nominal capacity | 200Ah |
| Communication | CAN/RS485/RS232 |
Quality Control
- Full-function test on every finished unit, not a sample from the batch
- Insulation and dielectric withstand testing on completed assemblies
- Aged and burn-in run before packing, so early-life failures happen in the factory
- Serialised traceability from cell batch to finished unit
- Packing inspection and photo record before container loading
Customization Options
- Mounting variant - wall, floor or rack - for the available space
- Label, manual and packaging language for the destination market
- Capacity configuration and number of parallel units
- Communication protocol matched to the inverter brand on site
How It Compares With The Alternatives
| Lead-acid batteries | Usable depth of discharge is far higher, so a lead-acid bank has to be specified much larger for the same usable energy - and replaced far sooner. |
|---|---|
| NMC lithium batteries | LiFePO4 gives up some energy density and gains thermal stability and cycle life, which is the trade most stationary storage buyers want. |
| A larger single battery | Parallel modules let the system be sized for today's load and extended later, instead of paying up front for capacity that idles for two years. |
Getting This Product Right On Site
- 1
Confirm the inverter model and communication protocol before ordering, so the handshake is verified not assumed
- 2
Mount in a dry, ventilated space within the stated operating temperature range
- 3
Torque terminals to the value in the manual and re-check after the first week of cycling
- 4
Set charge and discharge limits in the inverter to match the battery's rated current
- 5
Check the state-of-charge reporting and firmware version at each annual service visit
Lovsun IP65 Wall-mounted 5kWh 10kWh Lithium Battery - Buyer Questions
What temperature range can the battery work in
Which inverters is this battery compatible with
What is the minimum order quantity
How many units can be connected in parallel
What is the warranty and what does it cover
How is the battery packed for export
Other Lithium Battery Models
Background For This Specification Decision
Why a lead-acid bank has to be specified two to three times larger for the same usable energy, and what that does to the total cost over ten years.
Read the guide →Buying GuideHow To Size A Home Solar BatteryA method that starts from the evening load and the daily surplus rather than from the size of the PV array.
Read the guide →Design GuideHigh Voltage vs Low Voltage Battery SystemsWhy the DC bus voltage choice shows up in your cable schedule, your inverter options and your installation labour.
Read the guide →Homes and villas adding solar self-consumption and backup, where the installer needs a kit that works the same way on every job.
See the application →Telecom and Remote Off Grid SitesBase stations, monitoring installations and remote facilities where every site visit is expensive and the power system has to run unattended.
See the application →Commercial and Industrial SitesFactories, warehouses, cold stores and commercial campuses where the electricity bill is driven as much by demand charges as by consumption.
See the application →Request A Quote For Lovsun IP65 Wall-mounted 5kWh 10kWh Lithium Battery
Tell us the quantity, the destination market and the application. We reply within 12 hours with lead time, certification and pricing.