We reply to enquiries within 12 hours · Mon-Sat 08:30-18:00 GMT+8[email protected]+86 18155106856
Lithium Battery

Deye RW-M6.1-B 6kWh Lithium Battery

6 kWh

Deye RW-M6.1-B 6kWh Lithium Battery is a LiFePO4 storage battery rated at 6 kWh for solar self-consumption and backup duty.

Standards Referenced On The Original Datasheet

  • UN38.3
  • IEC62619
  • CE
Key Benefits

What This Product Changes On Your Project

  • No electrolyte maintenance, no equalisation charging and no ventilation requirement
  • LiFePO4 chemistry - a flatter thermal profile and a longer cycle life than NMC at the same usable energy
  • Integrated BMS with cell balancing, over-current, over-temperature and short-circuit protection
  • Parallel expansion, so a system can be sized for today's load and extended later without replacing the first units
  • Standard CAN and RS485 communication for inverter handshake, rather than a closed protocol that locks the buyer to one brand

Application Scenarios

  • Marine, RV and mobile installations replacing lead-acid banks
  • Residential solar self-consumption, storing midday PV for the evening load
  • Backup supply for homes and small offices on an unstable grid
  • Telecom and monitoring cabinets where a site visit is expensive
  • Off-grid cabins, farms and workshops running entirely on PV and storage

Who It Is For

  • System integrators building backup and off-grid packages
  • Telecom and infrastructure operators replacing lead-acid at remote sites
  • Off-grid property owners sizing a standalone power system
  • Solar installers specifying residential and light commercial storage

Problems It Solves

  • Replacement cycles every few years and the disposal cost that comes with them
  • Solar output exported at a low feed-in tariff and bought back at a high retail one
  • Outages that take critical loads down with no transfer time budget
  • Battery rooms that need ventilation, bunding and routine electrolyte maintenance

Technical Features

  • Parallel connection of multiple units to build capacity in steps
  • Enclosure and terminal layout designed for a single-installer fit
  • State-of-charge indication at the unit, not only through the inverter app
  • LiFePO4 cells with an integrated BMS handling balancing and protection
  • Over-voltage, under-voltage, over-current, over-temperature and short-circuit protection
Specifications

Published Specification Data

These figures come from the manufacturer datasheet for this model. Where a value you need is not listed, ask for the full datasheet rather than assuming a typical figure.

Energy capacity6 kWh
BrandDeye
Battery chemistryLiFePO4

Quality Control

  • Insulation and dielectric withstand testing on completed assemblies
  • Aged and burn-in run before packing, so early-life failures happen in the factory
  • Serialised traceability from cell batch to finished unit
  • Packing inspection and photo record before container loading
  • Incoming inspection of cells, power electronics and structural parts before assembly

Customization Options

  • Mounting variant - wall, floor or rack - for the available space
  • Label, manual and packaging language for the destination market
  • Capacity configuration and number of parallel units
  • Communication protocol matched to the inverter brand on site
Comparison

How It Compares With The Alternatives

Lead-acid batteriesUsable depth of discharge is far higher, so a lead-acid bank has to be specified much larger for the same usable energy - and replaced far sooner.
NMC lithium batteriesLiFePO4 gives up some energy density and gains thermal stability and cycle life, which is the trade most stationary storage buyers want.
A larger single batteryParallel modules let the system be sized for today's load and extended later, instead of paying up front for capacity that idles for two years.
Use Guide

Getting This Product Right On Site

  1. 1

    Check the state-of-charge reporting and firmware version at each annual service visit

  2. 2

    Confirm the inverter model and communication protocol before ordering, so the handshake is verified not assumed

  3. 3

    Mount in a dry, ventilated space within the stated operating temperature range

  4. 4

    Torque terminals to the value in the manual and re-check after the first week of cycling

  5. 5

    Set charge and discharge limits in the inverter to match the battery's rated current

Deye RW-M6.1-B 6kWh Lithium Battery - Buyer Questions

What is the warranty and what does it cover
Warranty terms are confirmed in writing with the quotation and depend on the model and destination market. Ask for the warranty statement before you place the order.
How is the battery packed for export
Units are packed to UN38.3 transport requirements for lithium batteries, with the documentation the carrier needs. Confirm air or sea freight when you enquire, as the requirements differ.
Can we order with our own branding
Yes. Enclosure finish, nameplate and packaging can carry your brand. Minimum quantities apply for custom labelling.
What temperature range can the battery work in
The operating and storage temperature ranges are in the specification table. Charging has a narrower window than discharging, which matters for unheated installations.
Which inverters is this battery compatible with
It communicates over CAN and RS485 and is used with common hybrid inverter brands. Tell us the exact inverter model you plan to use and we will confirm the protocol before you order.
What is the minimum order quantity
One unit for a sample or a single installation. Container quantities are priced for distributors and installers ordering to stock.

Request A Quote For Deye RW-M6.1-B 6kWh Lithium Battery

Tell us the quantity, the destination market and the application. We reply within 12 hours with lead time, certification and pricing.