
Single-Hole Solar Cable Entry Glands
Solar Cable Entry Single Hole Black
A bonded waterproof gland housing that takes one 6–12 mm solar cable through a roof or deck without a leak path.
- A permanent watertight seal around the cable, not a sealant repair that has to be redone
- Bonds to the surface — no fastener needs to pass through the roof
- Thick UV-resistant plastic with a large sealing area for a reliable bond
- Protects the electrical connection from weather for the life of the installation
Product overview
What It Is and What It Does
The panel is only half the job. Every roof-mounted array has to get its cable inside, and the hole that cable goes through is the single most common source of water ingress on a converted vehicle or a boat. This is a water-proof cable entry gland that seals to the roof or deck of a boat, yacht or caravan, so cable holes can be drilled and sealed without risk of leaking.
The housing is moulded from thick UV-resistant plastic with a large sealing area — the large footprint is deliberate, because a wide bond spreads the adhesive load and keeps the seal intact when the roof flexes. It takes 6–12 mm cable and provides a watertight seal to protect the electrical connection inside.
Who it is for
- Caravan, motorhome and van converters routing panel cable into a habitation area
- Boat and yacht electricians penetrating a deck or coachroof
- Shed, cabin and site-hut installers who need a sealed feed-through
- Solar accessory distributors selling complete fitting hardware
Problems it solves
- A bare drilled hole with sealant smeared over it fails within a season or two
- Water tracking down the cable into the roof void is invisible until the damage is done
- Cable chafing on a raw hole edge eventually cuts through the insulation
- A cable entry that has to be unbolted to service cannot stay watertight
Key benefits and features
Why Buyers Choose BS090028-B
Benefits
- A permanent watertight seal around the cable, not a sealant repair that has to be redone
- Bonds to the surface — no fastener needs to pass through the roof
- Thick UV-resistant plastic with a large sealing area for a reliable bond
- Protects the electrical connection from weather for the life of the installation
Technical features
- Single-hole waterproof cable entry gland
- Holds 6–12 mm cable
- Material: thick UV-resistant plastic, black
- Large sealing area for surface bonding
- For roof or deck of boat, yacht, caravan and vehicle
- Bonds to a clean surface with sealant, sold separately
| Product number | BS090028 |
|---|---|
| Colour | Black |
| Type | Single hole cable entry |
| Cable range | 6–12 mm |
| Material | Thick UV-resistant plastic |
| Packing | 100 pcs per outer carton |
| Fixing method | Bonded to a clean surface, sealant sold separately |
| Also known as | Solar mounting cable feed, solar cable feed gland |
| Suitable surfaces | Vehicle roof, caravan roof, boat and yacht deck |
Materials and manufacture
What It Is Made From
Thick UV-resistant plastic rather than a thin-wall moulding. The wall thickness is what lets the housing be bonded down hard and stay flat, and the large sealing area gives the adhesive enough surface to hold through roof flex and thermal movement.
Quality and certification
Everything in the BS090028-B table above is taken from our own product documentation — a 6–12 mm cable range. Nothing on this page is estimated or rounded up to make a better headline. If a tender needs a written certification or test statement, tell us which standard it names and we will say what we can supply.
Customisation
BS090028-B is the black version, and BS090028-W is the same part in white. The standard export pack is 100 pcs per outer carton. For a different pack quantity, a printed carton, or cable entry — single under your own label, tell us the annual volume you are planning and we will come back on what is possible and what it changes on price.
Comparison
How It Compares
Against the double-hole BS090025
Single hole for one cable run; double hole where a positive and negative pair both have to cross the roof line through one penetration.
Against a generic cable gland
A bare gland needs a threaded hole and a backing nut inside the roof. This one bonds to the outside and is designed to be sealed rather than clamped.
Against the white BS090028-W
Same housing in white for light-coloured roofs.
Use guide
How to Fit It
Step 1
Choose the cable route and drill a hole large enough for the cable only.
Step 2
Clean and degrease the surface around the hole.
Step 3
Bond the housing down over the hole with a suitable sealant.
Step 4
Pass the cable through the gland and tighten the lockring.
Step 5
Let the sealant cure fully before the vehicle is exposed to rain.
Questions
Frequently Asked Questions
What cable diameter does it take?
6 to 12 mm.
Is sealant included?
No. The housing is designed to be bonded to a clean surface with a sealant of your choice, sold separately.
How is it packed?
100 pieces per outer carton.
Can it be walked on?
The double-hole box in this range is specifically not recommended for surfaces that get walked on. Treat this housing the same way and route it clear of walkways.
Further reading
Notes and Guides for This Product

Two Panels on a Caravan Roof Without Drilling
A caravan owner planned to DIY-install two 80 watt polycrystalline panels on the roof of a 21 ft 6 in van. The question raised on…

Waterproof Roof Cable Entry on a Camper
When the cable assembly of solar panels on the roof of a camper is run, the practical route is to bring the cable through the…

No Drill Adhesive Mounting for Caravan Roofs
The reasoning behind the ABS range, and what changed when white was added.

ABS Plastic Versus Aluminium Solar Mounts
Two mounting families, one decision: can this surface take a fastener or not?
Ready to Order BS090028-B
Tell us how many BS090028-B you need and which port they are going to. We will confirm against the standard pack of 100 pcs per outer carton, quote freight and give you a lead time.


