Strip Light with 2835 Smd Led
The most versatile and cost-effective size, solving the problem of low brightness in small-chip models. Low voltage operation, no flicker, no UV radiation, and surface temperature <45℃ (touch-safe).
Product Overview
A flexible LED strip with 2835 SMD chips designed for general lighting in residential, commercial and task applications where brightness, flexibility and cost efficiency are balanced. The 2835 chip size offers higher output than smaller SMDs while maintaining a slim profile. The strip is bendable at any angle up to 180 degrees and cuttable at 5cm or 10cm intervals without damaging the circuit. Available in 12V or 24V DC, with 60, 120 or 168 LEDs per metre, and customizable power consumption. Rated from IP20 to IP68 depending on the version, it supports surface mounting in dry, damp or fully submerged environments. Suitable for kitchens, bathrooms, corridors, under-cabinets, TV backlighting and commercial spaces where consistent brightness and low heat are required.
Key Benefits
- 2835 SMD chips deliver higher brightness than smaller SMDs while maintaining a slim profile
- Bendable at any angle up to 180 degrees for fitting around curves and irregular surfaces
- Cuttable at 5cm or 10cm marked intervals without damaging the circuit or affecting performance
- Available in 12V or 24V DC to suit different run lengths and voltage drop requirements
- IP20 to IP68 protection levels allow use in dry, damp or fully submerged environments
- Power consumption is customizable based on LED quantity per metre
- Surface temperature below 45℃ makes it touch-safe in enclosed or close-proximity installations
- No flicker with PWM dimming, no UV radiation, and low heat output for safe indoor use
Problems It Solves
- Small SMD chips (e.g. 3528) produce insufficient brightness for general lighting tasks
- Rigid strips cannot follow curved surfaces without cutting or bending damage
- Fixed cut intervals prevent precise fitting to custom run lengths
- Low IP ratings limit use in bathrooms, kitchens or outdoor covered areas
- High surface temperature in some strips makes them unsafe near touch points
- Flicker from low-frequency dimming causes eye strain or video banding
- Lack of voltage options forces the use of longer runs with higher voltage drop
Application Scenarios
- Kitchen under-cabinet task lighting where consistent brightness and low heat are required
- Bathroom ceiling or wall strips in damp areas, using IP65 or higher versions
- Corridor lighting in homes or offices with curved wall runs
- TV backlighting behind a display where a continuous, even light is needed
- Retail shop lighting for product displays, using RGB or white 2200-6500K
- Hotel lobby or reception area lighting with curved wall or ceiling runs
- Office ceiling coves or edge lighting where a slim, flexible strip is needed
Who It Is For
- Lighting distributors sourcing a cost-effective, versatile strip for residential and commercial projects
- Electrical wholesalers stocking a flexible strip for general-purpose lighting
- OEM/ODM brands needing a customizable strip with 2835 SMD chips and variable IP rating
- Contractors specifying a strip for kitchens, bathrooms or corridors with curved runs
- Project buyers requiring a low-heat, touch-safe strip for enclosed or close-proximity installations
Engineering Detail
Technical Features
- 2835 SMD LED chips arranged in a linear array on a flexible PCB
- Bendable at any angle up to 180 degrees without damage to the circuit
- Cuttable at 5cm or 10cm marked intervals with no risk to electrical continuity
- Input voltage DC 12V or 24V, selectable based on run length and power needs
- IP20 for indoor dry use, IP65 for damp areas, IP66 for high-pressure washdown, IP68 for submersion
- Beam angle 120 degrees for wide, even light distribution
- Power consumption based on LED quantity: 7.2W, 14.4W, or 17.6W per metre
- Surface temperature below 45℃ under normal operation, touch-safe
- PWM dimming supported, flicker-free at standard dimming frequencies
Materials
- 2835 SMD LED chips with high-efficiency die and phosphor coating
- Flexible PCB with copper traces and solder mask for durability
- Encapsulated adhesive backing for surface mounting
- Polymer-based insulation layer protecting the circuit from moisture and dust
Specifications
Technical Data
Values taken from our product datasheet. Anything not listed here is confirmed per order.
| LED type | 2835 SMD |
|---|---|
| Model number | WK-FP2835-60D / 120D / 168D |
| PCB width | 8mm / 10mm |
| Input voltage | DC 12V / 24V |
| LED quantity | 60pcs / 120pcs / 168pcs per metre, customizable |
| Power consumption | 7.2W / 14.4W / 17.6W per metre |
| Colour temperature | 2200K - 6500K, R/G/B, single colour |
| CRI (Ra) | >80 / 90 / 95 |
| Beam angle | 120° |
| Lumens per LED | 24-26 lm |
| IP grade | IP20 / IP65 / IP66 / IP68 |
| Thickness | 2-3mm |
| Width | 8-12mm |
| Length | 1m / 2m / 5m / 10m, customizable |
| Cut interval | 5cm / 10cm marked intervals |
Manufacturing Process
- 2835 SMD LEDs mounted on flexible PCB at the selected density
- PCB cut to standard or custom length with marked cut intervals
- Adhesive backing applied to the back of the strip for mounting
- Electrical test performed on each run to verify continuity and voltage
- Final inspection and packaging before shipment
Quality Control
- Products are 100% tested before delivery
- Branded LED chips and high quality raw materials used in production
- IP rating verified per the ordered specification
- Colour temperature and CRI checked against the ordered value
Customization Options
- LED quantity per metre customizable to match brightness and power requirements
- Cut length and end termination to the buyer's run drawing
- IP rating selected based on environmental conditions (IP20 to IP68)
- Voltage (12V or 24V) chosen based on run length and driver compatibility
- Colour temperature from 2200K to 6500K, or RGB, specified per project need
Honest Comparison
How It Compares With the Alternatives
| 3528 SMD strip | 2835 offers higher brightness and better thermal performance than 3528, though at a slightly higher cost per metre |
|---|---|
| PVC-coated strip | This strip uses a flexible PCB with polymer insulation, which is more durable and heat-resistant than PVC, but less flexible in extreme cold |
| Rigid aluminium profile strip | This strip is fully flexible and can follow curves, but lacks the heat dissipation of an aluminium channel |
Use Guide
Getting the Best Out of It On Site
- Use 12V for short runs (under 5m) to reduce voltage drop and simplify driver selection
- Use 24V for long runs (over 5m) to maintain consistent brightness across the length
- Ensure cut intervals are respected to avoid damaging the circuit or voiding performance
- For IP65 or higher versions, ensure the ends are sealed properly to maintain protection
- Avoid continuous operation in enclosed spaces without ventilation if surface temperature is a concern
- Use PWM dimmers compatible with 12V or 24V DC to avoid flicker or noise
- Install with the adhesive side down on clean, dry, flat surfaces for optimal adhesion
Related Products
Others in This Range
Strip Light with 240pcs 3528 Smd Led
Its ultra-compact chip size (2.2×1.6mm) makes the light strip extremely thin and flexible, allowing it to bend freely...
View specifications →
Strip Light with 3528 Smd Led
The chip structure is simple and reliable, with low failure rates and wide compatibility with controllers and power...
View specifications →
Strip Light with 2216 Smd Led Double Color
Its ultra-compact chip size (2.2×1.6mm) makes the light strip extremely thin and flexible, allowing it to bend freely...
View specifications →
Strip Light with 2216 Smd Led
Its ultra-compact chip size (2.2×1.6mm) makes the light strip extremely thin and flexible, allowing it to bend freely...
View specifications →Where This Product Is Used
Technical Guides
Choosing Between 12V and 24V LED Strip Light
Compare 12V and 24V LED strip voltage drop, run length limits, driver compatibility, and current draw for commercial and
Read guide →SMD LED Types Compared 2835 3528 5050 and 2216
Compare SMD 2835, 3528, 5050, and 2216 LED types used in flexible strip lights. Learn which is best for space, brightnes
Read guide →IP20 IP65 IP67 and IP68 Explained for LED Strip and Fixtures
What each IP rating means for LED strips and fixtures. Which products have IP68, IP67, IP65, or IP20. Practical guidance
Read guide →Buyer Questions
Questions About Strip Light with 2835 Smd Led
What is the minimum order quantity?
Small order quantities are accepted. Send the run lengths and configuration you need and we will confirm the minimum for that setup.
Can the LED quantity and cut length be customized?
Yes. LED quantity per metre and cut length are customizable to match your project’s brightness and layout requirements.
Which voltage should I order, 12V or 24V?
12V is suitable for runs under 5m. 24V is recommended for longer runs to reduce voltage drop and maintain consistent brightness.
Is this strip suitable for bathrooms or outdoor use?
Yes, when ordered with IP65, IP66 or IP68 rating. IP20 is for dry indoor use only.
Can I cut the strip at any point?
No. Cut only at the marked 5cm or 10cm intervals to avoid damaging the circuit.
What colour temperatures and CRI are available?
2200K to 6500K single colour, R/G/B, with CRI Ra >80, >90 or >95 depending on the specification.
What payment methods do you accept?
Different payment methods are accepted. Confirm the terms with our sales team when the order is quoted.
Request a Quote for Strip Light with 2835 Smd Led
Send the quantity, colour temperature and any customisation you need. Our sales team will confirm the configuration, lead time and price.