Silicone LED Neon Flex Strip-DMX512 Control
DMX 512 Intelligent Control: Realize dynamic effects (chasing/fading) with multi-strip linkage
Product Overview
A silicone encapsulated LED strip with built-in DMX512 control for dynamic lighting effects across multiple connected runs. The strip uses RGB SMD LEDs with a DMX512 IC that enables master-slave synchronization, allowing coordinated color and brightness changes across long or complex installations. The 20×20 mm profile is fully encapsulated in UV-resistant silicone, providing IP67/IP68 waterproofing and protection against dust, corrosion and mechanical stress. Designed for continuous runs with pre-marked cut points and spliceable connectors, it supports 12V or 24V DC input and delivers a beam angle from 180° to 360°, depending on installation orientation. Available in 60 or 120 LEDs per metre with power consumption of 10W or 20W respectively.
Key Benefits
- DMX512 control enables synchronized dynamic effects across multiple strips without external controllers
- IP67/IP68 rating allows use in wet, dusty or corrosive environments including outdoor and commercial spaces
- Silicone housing resists UV degradation, maintaining color and flexibility over time
- Ultra-flexible profile bends to follow curves and irregular surfaces without cracking or delamination
- Pre-marked cut points and spliceable connectors allow custom run lengths and easy field assembly
- 12V or 24V DC input supports long runs with minimal voltage drop when using 24V
- Beam angle of 180° to 360° provides wide light dispersion for ambient or directional effects
- CRI Ra above 80 ensures accurate color rendering for dynamic RGB lighting in commercial and architectural settings
Problems It Solves
- Non-DMX strips require separate controllers for each run, increasing complexity and cost
- PVC or non-encapsulated strips fail in outdoor or high-moisture areas due to water ingress
- Fixed color or static brightness limits the ability to create dynamic lighting effects
- Rigid strips cannot follow curved or irregular surfaces without visible joints or stress points
- Lack of pre-marked cut points leads to inconsistent run lengths and field errors
- Low CRI in RGB strips results in washed-out or inaccurate color reproduction
- Voltage drop in long runs causes dimming at the far end when using 12V DC
Application Scenarios
- Building facades and landmark contours requiring synchronized color changes across multiple strips
- Stage backdrops and concert lighting where chasing, fading and animated sequences are needed
- Mall atriums and hotel lobbies with dynamic ambient wall lighting for branding or mood setting
- Residential ceiling coves and staircase walls with programmable color transitions
- Garden fences, park pavilions and pool edges where outdoor durability and waterproofing are required
- Exhibition halls and theme parks using interactive or responsive lighting sequences
- Bar and KTV interiors with real-time color changes synchronized to music or motion sensors
Who It Is For
- Lighting distributors seeking a programmable strip for architectural and entertainment projects
- Event and stage contractors needing multi-strip DMX control for live shows and installations
- Commercial project buyers specifying dynamic ambient lighting in retail or hospitality spaces
- OEM brands integrating DMX control into custom lighting fixtures or furniture
- Architectural lighting designers requiring IP67+ strips for outdoor or wet-area applications
Engineering Detail
Technical Features
- DMX512 IC built into the strip enables master-slave synchronization across multiple units
- Silicone housing provides full encapsulation with UV, dust and corrosion resistance
- IP67/IP68 rating ensures performance in wet, dusty or outdoor environments
- Ultra-flexible design allows bending to follow curves and irregular shapes
- Pre-marked cut points allow clean separation at defined intervals
- Spliceable connectors enable field assembly and run extension
- Beam angle ranges from 180° to 360° depending on mounting orientation
- Efficacy above 80 lm/W delivers efficient light output per watt
Materials
- RGB SMD LEDs with built-in DMX512 IC for control and synchronization
- UV-resistant, high-transparency silicone housing providing full encapsulation
- Flexible substrate carrying the LED array and control circuit
- Spliceable connectors for field assembly and run extension
Specifications
Technical Data
Values taken from our product datasheet. Anything not listed here is confirmed per order.
| LED type | RGB SMD |
|---|---|
| Model number | WK-SPxx-xx |
| Housing material | Silicone |
| Size | 20×20 mm / customizable |
| Input voltage | DC 12V / 24V |
| LED quantity | 60 pcs / 120 pcs per metre |
| Power consumption | 10W / 20W per metre |
| Color temperature | RGB |
| CRI (Ra) | >80 |
| Beam angle | 180° to 360° |
| Efficacy | >80 lm/W |
| IP grade | IP67 / IP68 |
| Control protocol | DMX512 |
| Cuttable | At pre-marked intervals |
| Spliceable | With connectors |
Manufacturing Process
- LED array and DMX512 IC assembled on flexible substrate at the specified density
- Full silicone encapsulation applied to achieve IP67/IP68 sealing and mechanical protection
- Pre-marked cut points added at standard intervals for field separation
- Spliceable connectors attached at both ends for modular assembly
- Electrical and DMX control test performed before packing
Quality Control
- Products are 100% tested before delivery
- Branded LED chips and high quality raw materials used on the production line
- DMX512 signal integrity and color consistency verified across multiple units
Customization Options
- LED quantity per metre set to 60 or 120 pcs depending on brightness requirement
- Strip size customizable to fit specific profile or mounting constraints
- Cut points and connector types specified to match the installation drawing
- Voltage input selected as 12V or 24V based on run length and power delivery needs
- DMX512 address settings configured per the project’s control layout
Honest Comparison
How It Compares With the Alternatives
| Non-DMX RGB strip | DMX512 enables synchronized multi-strip effects without separate controllers |
|---|---|
| PVC encapsulated strip | Silicone resists UV and corrosion better, lasts longer in outdoor or humid environments |
| Fixed-length strip with no cut points | Pre-marked cut points allow custom run lengths and reduce field waste |
Use Guide
Getting the Best Out of It On Site
- Use 24V DC for runs longer than 5 metres to reduce voltage drop
- Ensure DMX512 addresses are set correctly on each strip to avoid signal conflicts
- Splice connectors only with matching types to maintain waterproofing and signal integrity
- Avoid sharp bends below the minimum radius to prevent damage to the encapsulation
- Install in covered outdoor areas; IP67/IP68 protects against rain but not sustained immersion
- Use DMX512 master controller to manage multiple strips in a synchronized sequence
- Verify CRI Ra >80 for applications where color accuracy is critical, such as retail or hospitality
Related Products
Others in This Range
Silicone Flexible Wall Washing Strip – 16*16mm 48pcs Led
Precise Wall-Washing Effect: Narrow 15°–45° beam angle delivers even, shadow-free illumination on vertical...
View specifications →
Underwater LED Silicone Strip Light
IP68 full waterproof design for long-term underwater...
View specifications →
Silicone LED Neon Flex Strip-360° View
Unique 360° Lighting Effect: Unlike traditional side-emitting or top-emitting strips, it creates a seamless,...
View specifications →
Silicone LED Neon Flex Strip- Top View (all Sizes)
Top-view design directs light precisely upward, making it perfect for illuminating ceilings, coves, or overhead spaces...
View specifications →Where This Product Is Used
Technical Guides
Silicone Encapsulated Neon Flex for Wet and Outdoor Installations
Silicone neon flex offers IP68 waterproofing, UV resistance, and superior flexibility for underwater and outdoor applica
Read guide →IP20 IP65 IP67 and IP68 Explained for LED Strip and Fixtures
What each IP rating means for LED strips and fixtures. Which products have IP68, IP67, IP65, or IP20. Practical guidance
Read guide →Choosing Between 12V and 24V LED Strip Light
Compare 12V and 24V LED strip voltage drop, run length limits, driver compatibility, and current draw for commercial and
Read guide →Buyer Questions
Questions About Silicone LED Neon Flex Strip-DMX512 Control
What is the minimum order quantity?
Small order quantities are accepted. Send the run lengths and configuration you need and we will confirm the minimum for that setup.
Can the LED density and cut length be customized?
Yes. LED quantity per metre is customizable, and the strip is cut at pre-marked intervals to your specified run lengths.
Which voltage should I order, 12V or 24V?
12V and 24V DC are both available. 24V is recommended for longer runs to reduce voltage drop across the line.
Is this strip suitable for outdoor or wet environments?
Yes. It is rated IP67/IP68 with silicone housing that resists water, dust, UV and corrosion, making it suitable for outdoor and wet-area use.
Can multiple strips be linked and controlled together?
Yes. The DMX512 IC supports master-slave synchronization, allowing multiple strips to be linked and controlled as a single system.
What is the beam angle of the strip?
The beam angle ranges from 180° to 360° depending on how the strip is mounted and the viewing angle.
What payment methods do you accept?
Different payment methods are accepted. Confirm the terms with our sales team when the order is quoted.
Request a Quote for Silicone LED Neon Flex Strip-DMX512 Control
Send the quantity, colour temperature and any customisation you need. Our sales team will confirm the configuration, lead time and price.