SpO2 Sensor 9 Pin for Biolight K0222 Series 3.2M
SpO2 Sensor 9 Pin for Biolight K0222 Series 3.2M is a reusable SpO2 sensor with a 9 pin male connector and a 3.2M cable, built for Biolight monitors.
- Model NoTM-K0222AF-L / TM-K0222AS-L / TM-K0222PF-L (+5 more)
- Connector9 Pin Male
- Cable Length3.2M or Customized
- SpO2 TechnologyDigital
- ColourGray or Blue
- Monitor BrandsBiolight and Dixion
- Warranty6 months
- CertificationISO 13485 quality system, CE, FDA compliance
- CustomisationOEM and ODM available
Samples, datasheets and certificate copies are sent on request. Tell us the monitor model you are fitting.
Product Overview
It is documented as compatible with monitors from Biolight and Dixion, with the exact monitor models listed in the compatibility table below. The series carries 8 part numbers covering finger clip, silicone soft tip, neonatal silicone wrap, multi-site Y type, ear clip and veterinary animal clip variants in adult, pediatric and neonatal sizes. The sensor uses Digital SpO2 technology, which is the technology the listed monitors expect. Standard housing colour is gray or blue. Warranty is 6 months.
These are SpO2 Sensors 9 Pin compatible for Biolight, Sinohero.
Problems It Solves
Two-piece sensor systems fail at the junction between the probe and the extension cable. The connector loosens, the reading drops out mid-shift, and staff replace both halves. A one piece sensor removes that joint entirely, which is why it is the standard fit for wards that run the same monitor fleet for years.
For this item specifically: the part exists so a Biolight monitor already in service can keep being used when its original probe is damaged or discontinued.
Who It Is For
This part suits departments monitoring adult, pediatric and neonatal patients, anyone running Biolight monitors and distributors holding stock against a mixed monitor fleet.
- General wards and bedside monitoring
- Operating theatre and recovery
- Emergency department triage
- Ambulance and transport monitors
- Veterinary clinics using human-protocol monitors
Specifications
Every figure below is taken from the product documentation for this item. Where a value is not published we mark it TBC rather than estimating it.
| Name | SpO2 Sensor |
|---|---|
| Instrument Connector | 9 Pin Male |
| Length | 3.2M or Customized |
| Color | Gray or Blue |
| SpO2 Tech | Digital |
| Latex-Free | Yes |
| Sterile | No |
| Warranty | 6 months |
Model Numbers in This Series
Every variant below is a separate part number within the same series. Quote the code that matches the patient size and probe style you need.
| Model No | Description |
|---|---|
TM-K0222AF-L | Adult Finger Clip SpO2 Sensor |
TM-K0222AS-L | Adult Silicone Soft Tip SpO2 Sensor |
TM-K0222PF-L | Pediatric Finger Clip SpO2 Sensor |
TM-K0222PS-L | Pediatric Silicone Soft Tip SpO2 Sensor |
TM-K0222NW-L | Neonatal Silicone Wrap SpO2 Sensor |
TM-K0222MS-L | Multi-Site Y Type SpO2 Sensor |
TM-K0222VS-L | Veterinary Animal Clip SpO2 Sensor |
TM-K0222AE-L | Adult Ear Clip SpO2 Sensor |
Monitor Compatibility
This part is built for the monitors listed below, taken from our product documentation. A matching plug shape alone does not guarantee a matching signal, so confirm your exact model here before ordering.
| Biolight | AnyView A2, AnyView A3, AnyView A4, AnyView A5, AnyView A6, AnyView A7, AnyView A8, V6 |
|---|---|
| Dixion | D2, D3, D5, D6, D8, DS3, DS5, DS7 Medica D Logicare Series 2000 Sinohero AcuitSign M6 Sunnex Q5 Venni VI-1200MT, VI-300A |
Quality Control
This part is produced under our ISO 13485 quality management system with compliance to CE Mark and FDA regulations. It passes three inspection stages: IQC on the incoming connectors, wires, cables and terminals; IPQC through cutting, stripping, crimping, injection and assembly; and OQC on packing, labels, marks, appearance, dimensions and electrical performance before it is released.
Customisation Options
Cable length on this item is stated as 3.2M or Customized, so a non-standard length can be quoted. Under our OEM and ODM service the product features, branding, packaging and labelling are customised, and we handle the regulatory documentation for your target market.
Comparison With the Alternatives
Against a short sensor plus adapter, this one piece build removes the mid-cable connector and the failure that goes with it, at a higher cost per replacement. Against a disposable sensor it is cheaper per patient but needs reprocessing between uses.
Use Guide
- Confirm the monitor manufacturer and model against the compatibility table above.
- Check the connector on the monitor matches 9 Pin Male.
- Choose the patient size and probe style from the model table, then quote that part number.
- Apply the sensor to a clean, well-perfused site and keep the emitter and detector aligned opposite each other.
- Rotate the measurement site regularly on long recordings to protect skin integrity.
- Between patients, clean and disinfect reusable items under your own protocol; discard single-patient-use items.
What This Range Gives You
No mid-cable connector to work loose
Probe, cable and monitor plug are one assembly, so the most common failure point in a sensor system is not present.
Eight probe styles per monitor family
Most series are available as adult finger clip, adult silicone soft tip, pediatric finger clip, pediatric silicone soft tip, neonatal silicone wrap, multi-site Y type, adult ear clip and veterinary animal clip.
Cable length matched to the room
Standard lengths run 0.9M for transport monitors up to 3.2M for bedside installations, or a customised length on request.
Cleanable between patients
Latex-free housings are wiped and disinfected for reuse under your own reprocessing protocol.
Related Products
Other parts from the same category, often quoted alongside this one.
Questions About This Product
Which monitors does SpO2 Sensor 9 Pin for Biolight K0222 Series 3.2M fit
It is documented for monitors from Biolight and Dixion. The compatibility table on this page lists the exact model names. If your model is not there, send it to us with a photo of the monitor socket.
What connector does it use
The instrument connector is 9 Pin Male, on a 3.2M or Customized cable.
Which part number should I quote
The series has 8 part numbers. Pick the one matching the patient size and probe style you need from the model table above, and quote that code.
What warranty applies
6 months, as stated in the specification table for this item.
What does one piece mean exactly
The finger probe, the cable and the monitor connector are manufactured as a single assembly. There is no detachable extension cable in the middle.
Can I get the same sensor in a pediatric size
Yes. Most series carry adult, pediatric and neonatal variants under the same base model number, distinguished by a letter in the part code. The model table on each product page lists every variant in that series.
Can this be supplied under our own brand
Yes. OEM and ODM covers product features, branding, packaging and labelling, with the regulatory documentation handled for your market.
Quote SpO2 Sensor 9 Pin for Biolight K0222 Series 3.2M
Tell us the quantity and the monitor model you are fitting and we will confirm the part number and price.