The full fastener catalogue
Six families, 28 production lines, hundreds of size and finish combinations. Every specification here is buildable in custom sizes, finishes and packaging — browse by family, or send us a drawing.
01 / Chipboard Screws
Engineered for engineered wood.
Pozi & Phillips drive, white / yellow zinc, DIN 7505. Optimised for particleboard, MDF and softwood.
Chipboard Screws, White Zinc Plated
Bright zinc finish for indoor cabinetry, furniture and joinery work. Standard countersunk head with coarse single-lead thread.
Chipboard Screws, Yellow Zinc Plated
Yellow chromate finish — popular in European DIY and construction. Higher contrast and slightly improved corrosion resistance.
DIN 7505 Chipboard Screw
Strict DIN 7505 dimensional compliance. Pozi #2 drive. Preferred by joinery and timber-frame contractors across Europe.
Double Csk Head Chipboard Screw
Double countersunk head profile for solid clamping in MDF and dense particle board without chipping the surface.
Square Hole Chipboard Screw With Secanting
Square (Robertson) drive recess with secanting tip — superior tip-bite into hardwood and engineered panels.
02 / Drywall Screws
Bugle head, sunk flush, every time.
Bugle head, fine and coarse thread, black phosphate or Magni. Hi-Lo and self-drilling tip variants.
Drywall Screw, Hi-Lo Thread, Magni
Alternating tall and short thread profile for higher pull-out in soft substrates. Magni grey coating for outdoor or humid environments.
Drywall Screw, Phillips Bugle Head, Coarse Thread
Standard drywall-to-wood-stud screw. Sharp point bites quickly into softwood; bugle head sinks below the paper without breakthrough.
Drywall Screw, Phillips Bugle Head, Coarse Thread, Gray
Same coarse profile in grey phosphate finish — preferred by some markets for visual differentiation on the job site.
Drywall Screw, Phillips Bugle Head, Fine Thread
Fine thread for fastening drywall to light-gauge metal studs (25 ga and lighter). Reduces stripping; higher pull-out in metal.
Drywall Screw, Phillips Bugle Head, Self Drilling
Drill point eliminates pre-drilling on heavier-gauge steel studs. Combines the bugle head with a hardened mini-drill tip.
03 / Self-Drilling Screws
Drill, tap and fasten — in one drive.
Tek screws for sheet metal, hex washer head, EPDM bonded washer. DIN 7504K compliant.
Modified Truss Head Phillips Self-Drilling Screw
Wide low-profile modified truss head, Phillips drive. Distributes load over a larger area without pull-through.
Pan Framing Head Phillips Self-Drilling Screw
Pan framing head — slightly raised low-profile. Used for steel-stud framing where head clearance is tight.
Pan Phillips Head Self-Drilling Screw
Standard pan head with Phillips drive and self-drilling tip. The everyday sheet-to-sheet fastener.
Truss Head Self-Drilling Screw
Wide truss head with Phillips drive. Distributes load on lath, mesh and thinner sheet materials.
Window Drilling Screw, White Zinc
Specifically engineered for aluminium window-frame installation. White zinc finish.
04 / Roofing Screws
Color-matched, weather-sealed, decade-tested.
Color-matched heads, sealing washer, weather-resistant coatings for steel & metal roof panels.
Colored Roofing Screw, Self-Drilling
Painted head matched to roof panel color. Self-drilling tip eliminates pilot holes on steel purlins up to 5 mm.
DIN 7504K Self-Drilling Screw
Strict European-standard self-drilling roofing screw. Available with or without colored head.
Hex Washer Head Self-Drilling Screw with EPDM Washer
The classic roof and cladding fastener. Bonded EPDM rubber washer creates a watertight seal.
Roof Screw, Color Head
Painted head finish in standard RAL colors. For metal roofing systems where appearance matters as much as performance.
Roofing Screw, Zinc, Self-Drilling
Zinc-plated finish, self-drilling point. The general-purpose utility roofing screw.
Roofing Screw, Color Hex Head, Self Drilling
Color-coated hex head with hardened drill point — for color-matched installation on coated metal panels.
05 / Self-Tapping Screws
They cut their own thread — and hold it.
Pan, truss and countersunk heads. Form their own thread in metal, plastic and timber.
High-Low Thread Countersunk Tapping Screw
Alternating high and low thread profile in a countersunk head — superior holding in plastic and softer substrates.
Pan Framing Head Phillips Self-Tapping Screw
Pan framing head, Phillips drive. Slim profile for sheet metal framing and electrical box assembly.
Truss Head Self-Tapping Screw
Wide low-profile truss head distributes load. Common in HVAC, electrical enclosures and signage.
Truss Head Self-Tapping Screw, Color Head
Color-coated truss head — for visible installations where finish color matters.
Window Tapping Screw, Yellow Zinc
Engineered for aluminum window-frame assembly. Yellow zinc finish for corrosion resistance and visual differentiation.
06 / Wood Screws
Heavy-duty timber fastening.
Hex washer head and hex flange Torx-drive wood screws. M6–M20, 35–200 mm, zinc plated.
Hex Washer Head Wood Screw
Hex washer head, zinc plated, M6–M20 diameter range. Heavy-duty fastener for structural timber and timber-to-metal.
Hex Flange Wood Screw, Torx
Hex flange head with Torx drive — high-torque application without cam-out. Premium choice for structural decking, pergolas and outdoor timber framing.
Materials & finishes
Specify your steel, head, drive and finish — we build to drawing
Materials
SAE 1018 / 1022 / 10B21 carbon steel, 304 / 316 stainless steel, plus brass and bi-metal options.
Head shapes
Bugle, pan, truss, hex washer, hex flange, countersunk, button, wafer, modified truss.
Drive types
Phillips, Pozi, Torx, hex socket, square, slotted — single or combination drives.
Finishes
White zinc, yellow zinc, black phosphate, Ruspert, Magni, electrophoretic and colour polymer coatings.
Need a custom specification?
Send a drawing, a sample or even a photo from the job site. Our engineers reverse-engineer it and quote within 24 hours.