Finger Clip Kits for Adult SpO2 Sensor PJ501-S03
Finger Clip Kits for Adult SpO2 Sensor PJ501-S03 is a replacement component, built for Adult SpO2 Sensor monitors.
- Model NoTM-PJ501-S03
- ColourGray or Blue
- Warranty12 months
- CertificationISO 13485 quality system, CE, FDA compliance
- CustomisationOEM and ODM available
Samples, datasheets and certificate copies are sent on request. Tell us the monitor model you are fitting.
Product Overview
It is supplied under part number TM-PJ501-S03. Standard housing colour is gray or blue. Warranty is 12 months.
These are kits for adult finger clip SpO2 Sensors.
Problems It Solves
A dropped finger clip usually breaks the plastic housing, not the optics. Holding the right spare part turns a discarded sensor into a ten-minute bench repair for biomedical engineering.
For this item specifically: the part exists so a Adult SpO2 Sensor monitor already in service can keep being used when its original probe is damaged or discontinued.
Who It Is For
This part suits departments monitoring adult patients, anyone running Adult SpO2 Sensor monitors and distributors holding stock against a mixed monitor fleet.
- In-house biomedical repair benches
- Distributors offering an after-sales repair service
- Fleet operators holding consumable spares
Specifications
Every figure below is taken from the product documentation for this item. Where a value is not published we mark it TBC rather than estimating it.
| Name | Finger Clip Kits |
|---|---|
| Patient | Adult |
| Color | Gray or Blue |
| Latex-Free | Yes |
| Sterile | No |
| Warranty | 12 months |
Model Numbers in This Series
Every variant below is a separate part number within the same series. Quote the code that matches the patient size and probe style you need.
| Model No | Description |
|---|---|
TM-PJ501-S03 | Finger Clip Kits for Adult SpO2 Sensor |
Monitor Compatibility
This part is built for the monitors listed below, taken from our product documentation. A matching plug shape alone does not guarantee a matching signal, so confirm your exact model here before ordering.
| Compatible with | Adult > 40 KGS |
|---|
Quality Control
This part is produced under our ISO 13485 quality management system with compliance to CE Mark and FDA regulations. It passes three inspection stages: IQC on the incoming connectors, wires, cables and terminals; IPQC through cutting, stripping, crimping, injection and assembly; and OQC on packing, labels, marks, appearance, dimensions and electrical performance before it is released.
Customisation Options
Connector, cable length and packaging can be quoted to your specification. Under our OEM and ODM service the product features, branding, packaging and labelling are customised, and we handle the regulatory documentation for your target market.
Comparison With the Alternatives
Compared with replacing the complete assembly, this part restores the equipment at a fraction of the cost and without a new qualification exercise.
Use Guide
- Confirm the monitor manufacturer and model against the compatibility table above.
- Check the connector on the monitor matches the connector stated in the specification table.
- Choose the patient size and probe style from the model table, then quote that part number.
- Apply the sensor to a clean, well-perfused site and keep the emitter and detector aligned opposite each other.
- Rotate the measurement site regularly on long recordings to protect skin integrity.
- Between patients, clean and disinfect reusable items under your own protocol; discard single-patient-use items.
What This Range Gives You
Repair instead of replace
Spare housings, clips and components keep serviceable optics and cable in use.
Matched to our own sensor families
Parts are made to the same moulds as the sensors they belong to.
Useful stock for biomed departments
Low-cost items to hold against the failures that happen most often.
Latex-free materials throughout
Consistent with the sensors they are fitted to.
Related Products
Other parts from the same category, often quoted alongside this one.
Questions About This Product
What is the part number
TM-PJ501-S03 - Finger Clip Kits for Adult SpO2 Sensor.
What warranty applies
12 months, as stated in the specification table for this item.
Which sensors do these parts fit
Each part page states what it is used for. Tell us the sensor part number and we will confirm the matching component.
Do you supply parts for other manufacturers' sensors
Our spare parts are made for our own sensor families. Send a photo and the monitor model and we will tell you whether a part fits.
Is there a minimum order on spare parts
Minimum order quantity depends on the item; ask by WhatsApp or email with the part number and we will confirm.
Are replacement parts covered by warranty
Warranty terms are stated per item on the product page.
Can this be supplied under our own brand
Yes. OEM and ODM covers product features, branding, packaging and labelling, with the regulatory documentation handled for your market.
Quote Finger Clip Kits for Adult SpO2 Sensor PJ501-S03
Tell us the quantity and the monitor model you are fitting and we will confirm the part number and price.