Line Tap Connector

Compression connectors in H-shaped

Compression connectors in H-shaped is generally used in connection of jumper wires, branch lines,lead wires,service mains.

  • Compression branch connectors and sealing kits Tool detail see CROP Tool: CRH-TU
Request A Quote Email Us Request A Sample
GroupPower Connectors
CategoryLine Tap Connector
StandardsIEC and GB
CustomisationOEM and non standard accepted
Compression connectors in H-shaped
OverviewSpecificationsGalleryOrderingFAQRelated

Overview

Compression Connectors in H-shaped Description

Description of Compression Connectors in H-shaped

Compression connectors in H-shaped is generally used in connection of jumper wires, branch lines,lead wires,service mains and other wires on the tower in overhead high-voltage and low-voltage power line, suitable for aluminum or copper wire.

For ACRS, aluminum or copper conductors in various deadend terminal. For cable taps and earth grid ring mains. Sector-shaped conductors must be rounded with round-forming dies.

H Shaped Aluminum Connector can connect two wires of equal diameter and different diameter. The span of wires in the same slot is generally 3-4 specifications. When the H-shaped parallel groove clamp is connected to the wire, due to the ring force, the aluminum on the inner wall of the clamp is plastically deformed, and it is embedded in the twisted gap of the outer layer of the wire, and the effective contact surface is large. The H-shaped parallel groove clamp pairs the wire The grip strength is about 40%-65% of the calculated breaking force of the wire.

Specifications

Codes Ranges and Dimensions

Figures below are reproduced from the CROP catalogue for this item.

ModelsCRH-11CRH-22CRH-41CRH-21CRH-31CRH-32
Outer DimaterRun “A” (mm)4.8-8.210.0-14.016.2-22.48.3-14.013.0-22.413.0-22.4
Run “B” (mm)4.8-8.210.0-14.016.2-22.44.8-9.64.8-11.411.6-16.0
Conductor SizeRun “A” (mm²)16-3550-95150-24050-9595-24095-240
Run “B” (mm²)16-3550-95150-24016-5016-7070-150
Insulate Sleeve’s ModelsPlastic TypeJH-1JH-2JH-3JH-2JH-2JH-2
Rubber TypeLHZ-1LHZ-2LHZ-3LHZ-2LHZ-2LHZ-2

Ordering and Support

From Enquiry To Delivered Order

1

Send The Requirement

Item code, conductor or cable size and quantity, or a drawing and a photograph for a non standard part.

2

Quotation

Price, packing, carton quantity and lead time are confirmed against the catalogue reference.

3

Sample or Tooling

Samples are sent for approval. Parts that need a new mould go through the in house mould division.

4

Production and Shipment

Production to IEC and GB standards, then packing and shipment on the agreed terms.

Answers

Frequently Asked Questions

How do I choose the right size?
Match your conductor or cable size against the range column in the specification table on this page, then quote the code on that row. If the size falls between two rows, send both figures with your enquiry and the correct item will be confirmed.
Is Compression connectors in H-shaped available as a sample before a production order?
Yes. Ask for a sample by WhatsApp on 0086 138 6832 9796 or by email and the item, the packing and the lead time for a full order will be confirmed together.
Which standards do CROP products follow?
All CROP products are made to comply with IEC and GB standards. Where a project calls for a national or utility specification, send the standard reference with your enquiry and the matching item will be quoted.
Can items be produced to our own drawing?
Yes. Non-standard and OEM orders are part of the normal range. Send the drawing, a picture, the weight or the written specification to [email protected] or by WhatsApp and a quotation will be prepared against your requirement. CROP also runs its own mould division for plastic, SMC and stamped parts.
How do I obtain the PDF catalogue?
The catalogue is issued on request. Ask for the section you need by email or WhatsApp on 0086 138 6832 9796 and the PDF will be sent back to you. The catalogue page lists every section that is available.

Next Step

Get A Price For Compression connectors in H-shaped

Send the code, the size and the quantity. Drawings for non standard versions are welcome.

Chat on WhatsApp Email Us
Chat on WhatsApp